494984
19
Zoom out
Zoom in
Previous page
1/49
Next page
19
ENGLISH
Adjusting the riving knife
3
Note:
The riving knife has been cor-
rectly set at the factory. Readjustment
prior to initial operation is only required
should the riving knife have become mis-
adjusted in transit.
1. Raise saw blade fully.
2. Checking the riving knife:
Distance between the saw
blade's outer edge and the riving
knife needs to be 3 – 5 mm.
The riving knife must be in align-
ment with the saw blade.
A
Danger!
The riving knife is one of the
safety devices and must be correctly
installed for safe operation.
Only if realignment of the riving knife is
necessary:
3. Loosen table insert (49) and remove
from table.
Setting the distance to the saw blade:
4. Loosen hexagon socket head cap
screw
(50) (to do so, turn hexagon
socket head cap screw counter-
clockwise!)
5. Pull riving knife (51) fully up against
the stop and align: the gap between
saw blade and riving knife must be 3
to 5
mm.
6. Tighten hexagon socket head cap
screw
(50) (to do so, turn hexagon
socket head cap screw clockwise!)
Lateral alignment:
riving knife and saw blade (52) must be
in true alignment.
7. Loosen hexagon nut (53) and adjust
vertical alignment with machine
screw (54).
8. Lock machine screw with (53).
9. Loosen both hexagon socket screws
(55).
10. Align riving knife flush with the saw
blade.
11. Tighten both hexagon socket
screws (55).
12. Reinstall table insert.
Blade guard installation
1. Raise saw blade fully.
2. Install blade guard (57) on riving
knife (56).
7.2 Installation
There are two ways to ensure a firm
stand of the machine:
mounted on floor stand
(accessory);
mounted on sturdy table or bench.
7.3 Mains connection
B
Danger! High voltage
Operate this machine in dry sur-
roundings only.
Operate machine only on a power
source meeting the following
requirements (see also “Techni
-
cal Specifications”):
outlets properly installed,
earthed, and tested.
mains voltage and system fre-
quency conform to the voltage
and frequency shown on the
machine´s rating label;
fuse protection by a residual
current operated device (RCD)
of 30
mA sensitivity;
System impedance Z
max
at the
interconnection point (house
service connection) 0.35 Ohm
maximum.
3
Note:
Check with your local Electricity
Board or electrician if in doubt whether
your house service connection meets
these requirements.
Position power supply cable so it
does not interfere with the work
and is not damaged.
Protect power supply cable from
heat, aggressive liquids and
sharp edges.
Use only rubber-jacketed exten-
sion cables with sufficient lead
cross-section (see “Technical
Specifications”).
Do not pull on power supply
cable to unplug.
49
50
51
52
53
54
55
56 57
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info