494984

Metabo TS-250 Manual

20
Zoom out
Zoom in
Previous page
1/49
Next page
20
ENGLISH
A
Risk of injury!
This saw may only be operated
by one person at a time. Other per-
sons shall stay only at a distance to
the saw for the purpose of feeding or
removing stock.
Before starting work, check to see
that the following are in proper work-
ing order:
− power cable and plug;
− ON/OFF switch
− riving knife
− blade guard
− feeding aids (push stick, push
block and handle).
Use personal protection gear:
− dust respirator;
− hearing protection;
− safety goggles.
Assume proper operating position:
− at the front of the saw;
− in front of the saw;
− to the left of the line of cut;
− when working with two persons,
the other person must remain at
an adequate distance to the saw.
If the type of work requires, use the
following:
− suitable workpiece supports – if
otherwise workpiece would fall
off the table after cutting;
− dust collector.
Avoid typical operator mistakes:
− Do not attempt to stop the saw
blade by pushing the workpiece
against its side. Risk of kickback.
− Always hold the workpiece down
on the table and do not jam it.
Risk of kickback.
− Never cut several workpieces at
the same time – and also no bun-
dles containing several individual
pieces. Risk of personal injury if
individual pieces are caught by
the saw blade uncontrolled.
c
Drawing-in/trapping hazard!
Never cut stock to which
ropes, cords, strings, cables or wires
are attached or which contain such
materials.
8.1 Dust collector
A
Danger!
Dust of certain timber species
(e.g. beech, oak, ash) can cause can-
cer when inhaled. Use suitable dust
collector when working in enclosed
spaces. The dust collector must meet
the following requirements:
− hoses to fit outer diameter of dust
extraction ports (blade guard 38
mm; chip case 58 mm);
− air flow volume ≥ 460 m
3
/h;
− vacuum at dust extraction port of
saw ≥ 530 Pa;
− air speed at dust extraction port
of saw ≥ 20 m/ s.
The dust extraction ports are located at
the chip case assembly and at the saw
blade guard.
Observe the dust collector's operating
instructions as well!
Operation without a dust collector is only
possible:
− outdoors;
− for short-term operation
(up to a maximum of 30 minutes);
− with dust respirator.
A
Danger!
By the revolving motion of the
saw blade saw dust is blown from the
chip case.
A
Caution!
The dust extraction port must
not be blocked by objects.
8.2 Setting the depth of cut
A
Danger!
Parts of the body or objects in
the setting range can be caught by
the running saw blade! Set depth of
cut only with saw blade at standstill!
The saw blade's cutting height needs to
be adapted to the workpiece height: the
blade guard shall rest with its front edge
on the workpiece.
• Adjust depth of cut by turning the
handwheel (58) as required.
3
Note:
To compensate for possible play
in the blade height setting mechanism,
always raise the blade to the desired
position.
8.3 Setting the saw blade tilt
A
Danger!
Parts of the body or objects in
the setting range can be caught by
the running saw blade! Set the depth
of cut only with the saw blade at
standstill!!
The saw blade tilt is adjustable between
-1.5 ° and 46.5°.
1. Release lock lever (59).
2. Set required saw blade tilt.
3. Lock the set bevel tilt by tightening
the lock lever (59).
8.4 Sawing
A
Danger!
Always use push stick if dis-
tance between saw blade and rip
fence is less than 120 mm.
1. Set blade tilt and lock in position.
8. Operation
58
59
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info