494984
22
Zoom out
Zoom in
Previous page
1/49
Next page
22
ENGLISH
9.2 Adjusting the scale's
pointer
1. Loosen pointer fixing screw and
adjust pointer
(65) to indicate the
exact Zero position.
2. Retighten pointer fixing screw.
9.3 Adjusting the scale's
pointer
1. Align rip fence with saw blade.
2. Loosen ripfence pointer fixing screw
(66).
3. Bring both pointers (rip fence and
scale) in line.
4. Retighten ripfence pointer fixing
screw
(66).
9.4 Adjusting the mitre fence
stops
The mitre fence's positive stops at both
45° positions and the 90° position are
adjustable.
1. Loosen the mitre fence locking han-
dle.
2. Set mitre fence to any positive stop
position and lock with locking handle.
3. Loosen locking nut (67) and turn
screw (68) so far out, until flip stop
(69) can be turned forward.
4. Turn screw (68) in until it just
touches the flip stop (69).
5. Tighten locking nut. The flip stop
should move without difficulty.
9.5 Adjusting the blade tilt stop
1. Set release lever (70) horizontal and
let engage (0° bis 45°).
2. Release lock lever (72) and set saw
blade tilt to 0°/45°.
3. Lock set bevel tilt by tightening lock
lever (72).
4. Check blade bevel angle:
0°square with the saw table
45°with separate mitre square.
If these angles are not exactly
matched:
5. Adjust cam plates (71) of stops until
blade tilt against the saw table at
end positions is exactly 0°= square)
and 45°respectively.
3
Note:
To adjust the bevel tilt stop for
-1.5° to 46.5°, the release lever must be
pulled out and set into vertical position.
9.6 Saw Cleaning
Remove chips and saw dust with
vacuum cleaner or brush:
from saw blade setting guide ele-
ments;
from motor vent slots;
chipcase.
Cleaning the chipcase.
If there is sawdust build-up in the chip-
case, the chipcase needs cleaning:
3
Note:
The chipcase is accessible from
below only. For cleaning, both table
insert and saw blade may be removed.
1. Loosen screw (74) only slightly.
2. Remove thumb screw (75).
3. Turn lid (73) 180°.
4. Clean chipcase.
5. Close lid (73) again, turn in thumb
screw (75). Then tighten both
screws (74), (75) hand-tight only.
9.7 Saw storage
A
Danger!
Store saw so that
it cannot be started by unauthor-
ized persons, and
nobody can get injured.
A
Caution!
Do not store saw unprotected
outdoors or in damp environment.
9.8 Maintenance
Before switching ON
Visual check to see if
distance saw blade – riving knife is
5
mm maximum;
riving knife is in line with saw blade.
Visual check of power cable and power
cable plug for damage; if necessary
have damaged parts replaced by a qual
-
ified electrician.
Monthly (if used daily)
Remove saw dust and chips with vac-
uum or brush; apply light coat of oil to
guide elements:
threaded rod and guide rods of
blade rise and fall mechanismn:
swivel segments.
Every 300 hours of operation
Check all screwed joints, retighten if
necessary.
Before cutting a workpiece to size
make trial cuts on pieces of scrap.
Always place a workpiece on the
saw table in such way that it cannot
tilt or rock (e.g. always place a
65
66
67 68
69
70
72
71
10. Tips and Tricks
75 74 73
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info