494984
23
Zoom out
Zoom in
Previous page
1/49
Next page
23
ENGLISH
curved board on the table with the
convex side up).
To simplify repetitive cut-off work
use a stock stop .
Keep surface of table clean.
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A Floor Stand
Provides for a secure machine
stand and optimal working height;
ideal in mobile use, folds up for sav-
ing space.
B Dust Collection Attachment
Helps to protect your health and to
keep the shop clean.
C Roller/Ball Transfer Stand
For accurate guiding of long stock.
D TCT Saw Blade
250 x 2.8/1.8 x 30, 60 ATB teeth,
15° rake, 2 pinholes
For rip and cross cuts in grown tim-
ber and particle board.
E TCT Saw Blade
250 x 2.8/1.8 x 30, 80 ATB teeth,
10° rake, 2 pinholes
For rip and cross cuts in panels;
plastic, aluminium, copper extru-
sions and high-grade veneered
sheets.
F TCT Saw Blade
250 x 2.8/2.0 x 30, 80 square/trap-
ezoidal teeth, 5° negative rake, 2
pinholes
General purpose blade for plastics,
thin-walled aluminium-, copper-,
brass- and steel extrusions as well
as for panels, laminates and
veneered sheets.
A
Danger!
Repairs to electric tools must
be carried out by qualified electri
-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun
-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua
-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine-free
bleaching process.
A
Danger!
Before carrying out any fault service
or maintenance work, always:
1. switch machine OFF;
2. unplug power cable;
3. wait for saw blade to come to
standstill.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
Restart machine.
No mains voltage
Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
Remove cause for overheating, let
cool off for a few minutes. Then
press Reset button and restart
machine.
Stated top speed is not reached
Motor supply voltage too low:
use a shorter extension cable or
extension cable with larger lead
cross section (
1.5 mm
2
).
Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
Replace saw blade (see chapter
“Maintenance”).
Dust spout blocked
No dust collector connected or suction
capacity insufficient:
connect dust collector, or
increase suction capacity (air speed
20 m/sec at chip ejection tube).
11. Available Accessories
12. Repairs
13. Environmental Protection
14. Trouble Shooting
15. Technical specifications
Voltage V 230 (1 50 Hz) 110 V (1 50 Hz)
Wattage power input P1
power output P
2
kW
kW
2.0 kW S6 40%
1.2 kW S6 40%
1.55 kW S6 40%
0.84 kW S6 40%
Current draw A 9.6 15.5
Fuse protection min. A 16 (time-lag)
Protection class IP 20 IP 20
Rated no-load speed (at 230V) min
-1
3950 3900
Cutting speed (at 230V) m/s 51.7 50.1
Saw blade diameter (outer) mm 250 250
Saw blade arbor bore diameter (inner) mm 30 30
Kerf width mm 2.8 2.8
Depth of cut with saw blade vertical
at 45° saw blade tilt
mm
mm
0 ... 77
0 ... 51
0 ... 77
0 ... 51
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info