786811
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
3.4.2 MasterBus (optional)
The Mass Systemswitch is compatible with the MasterBus
network: a fully decentralized data network for
communication between Mastervolt devices such as the
inverter, battery charger, generator, batteries and many
more. See section 5 for details.
3.5 LOAD ON INVERTER MODE
The Short break output is transferred between the
generator input, shore input and inverter input, depending
on its availability. However, to prevent the generator from
an overload situation or to prevent the shore fuse from
tripping, the load that is connected to the Short break
output can be switched either manually or automatically
from the generator or shore power to the output of the
inverter. We call this the “load on inverter mode” or the
“force to inverter mode”.
When the load on inverter mode is switched OFF (figure
3), the Mass Systemswitch is in normal state. This means
that the Short break output is transferred between the
generator input, shore input and inverter input, depending
on the availability.
When the load on inverter mode is switched ON (figure 4),
power from the generator or the shore can no longer be
used to supply the Short break output. The Short break
output will only be supplied by the inverter. See the
manual of the remote operation panel to toggle the load on
inverter mode manually.
Figure 3: Load on inverter mode is OFF, while power from
the generator or the shore is available
Figure 4: Load on inverter mode is ON, while power from
the generator or the shore is available
3.6 AUTOMATIC LOAD ON INVERTER MODE
It is also possible to toggle the load on inverter mode
automatically. Then the load on inverter mode will be
switched ON when the current on the shore input or the
generator input exceeds a predefined set point. Then we
call it the automatic load on inverter mode” or the
automatic force to inverter mode”.
3.6.1 Traditional remote control panel
If a traditional remote control panel is applied, the
“automatic load on inverter mode” can be triggered by:
- The generator current (delayed)
- The shore current (not delayed)
To adjust the settings of the automatic load on inverter
mode refer to ADVANCED A-menu of the manual of the
remote operation panel.
3.6.2 MasterBus
If the Mass Systemswitch is controlled by MasterBus,
operation of the “automatic load on inverter mode” can be
programmed by means of an event-based command. See
section 6.3 for details. Refer to the manual of the
MasterBus remote panel for details about programming of
event-based commands.
3.6.3 Example
See figure 5. A coffee machine is switched on, causing an
extra load on the shore/generator. When the total load that
is connected to the shore or the generator exceeds its
maximum current level, first a time delay is triggered. After
this delay time the automatic load on inverter mode will be
activated: a part of the total load is switched from the
generator/ shore to the AC output of the inverter. When
the automatic load on inverter mode is activated, it is
switched off again when the adjusted time has elapsed.
Generator
or shore
Generator
or Power
Inverter
Short break
Generator
or shore
Generator
or Power
Inverter
Short break
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mastervolt Mass Systemswitch 16 kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mastervolt Mass Systemswitch 16 kW in the language / languages: English as an attachment in your email.

The manual is 1.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info