494340

Marmitek IR Control Pro System Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
6. STATUS IN: You can send a Power Status signal to the IR module by connec-
ting a Power adapter to this connection (not supplied; 12VDC/200mA),
which is switched by the device to be controlled. This will be continuously illu-
minated if the IR Receiver also has a status LED.
7. IR IN: Mini jack input for infrared signals (+12V, GND, ST OUT and IR IN).
8. ATTACHMENT HOLES (mounting material not supplied).
DIP switches
• EM ON / BL ON
’BL’ must be set to ‘ON’ if an IR Extender Cable with Blaster is connected to
one of the two outputs (3). This ensures a higher power on the
Emitters/Blasters output which is necessary. Switch it to ‘EM ON’ if you have
connected an IR Extender Cable with LED to this output or not connected
anything at all.
NOTE: The wrong choice when it comes to these two settings can damage
the IR Extender Cable and cause it to become defective.
• NET OFF / NET ON:
Switch to setting ‘NET ON’ if you have extended the IR Receiver’s cable by
more than 15 metres (maximum 300 metres with CAT5). This setting pre-
vents problems with ‘high data rate’ IR codes. If you use parallel numerous IR
Modules in the same network (see, page 40/41 for an example), ensure that
there is only one IR Module with the ‘NET ON’ setting. The switch will be set
to ‘NET OFF’ in all other situations.
3. INSTALLATION
To check the proper working of the system it is advisable first to test the forma-
tion as planned. For this reason connect everything as described as follows but
don’t fix or screw the components yet.
1. Mount the IR Module in an accessible place behind or alongside your A/V
equipment, in the vicinity of a socket (100-240Volt 50/60Hz). Make sure you
take the cable length of the IR Extender Cable into account and try to ensu-
re that the connections remain as accessible as possible.
5IRCP System Module 200™
ENGLISH
IRCP200_UG_80x120 12-01-2010 14:53 Pagina 5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek IR Control Pro System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek IR Control Pro System in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info