494340

Marmitek IR Control Pro System Manual

7
Zoom out
Zoom in
Previous page
1/44
Next page
5. TECHNICAL DATA
IR System Module
Supply Power: 100-240VAC 50/60Hz, 12VDC 1.2A (supplied)
Power STATUS: 12VDC 200mA. plug, - 5.5mm outside /
+ 2.1mm inside (not supplied)
IR LED: 2x 3.5mm mini jack plug (mono)
IR LED/Blaster: 2x 3.5mm mini jack plug (mono)
IR Receiver connection: 1 Connector for a maximum of 3 parallel
connected IR Receivers. Extendable up to
300 metres via CAT5 (or equivalent)
Dimensions: 79 x 52 x 26mm
6. COMPONENTS AVAILABLE
IR Receivers
Each system needs a minimum of one IR Receiver (maximum of 3). You can use
an extra IR Receiver to operate your A/V equipment from another room. See
datasheets for the IR Receivers on www.marmitek.com.
Dual-band IR Receivers
New, disruption-suppressing technology for use in the vicinity of Flat Screens
(such as Plasma, LCD and LED screens), direct sunlight and energy-saving bulbs.
Art.nr. 08003 - IRR3856S (separate receiver)
Art.nr. 08004 - IRR3856P (built-in receiver)
Broadband IR Receivers
Broadband Receiver 30 – 90 kHz is suitable for almost every brand and model of
A/V equipment.
Art.nr. 09734 - IRR3099S (separate receiver)
Art.nr. 09733 - IRR3099P (built-in receiver)
Art.nr. 08005 - IRR3099T (Table-TOP receiver)
IR LEDs (1 or 2 LEDs per cable)
Each system needs a minimum of one IR Extender Cable (maximum 4). The IR
Extender Cables with LEDs must be stuck to the A/V device that you wish to ope-
rate. The blinking LED version lights up if you send an infrared command with
the remote control. The non-blinking LED just passes the command onto the
device but does not light up.
Art.nr. 09777 - IRCP blinking 2 LED
Art.nr. 09843 - IRCP non-blinking 2 LED
Art.nr. 08007 - IRCP blinking 1 LED
Art.nr. 08008 - IRCP non-blinking 1 LED
You can use IR LEDs to operate a maximum of 8 A/V devices (4x IR Extender
Cables with 2 LEDs)
See datasheet for the IR LEDs on www.marmitek.com.
7IRCP System Module 200™
ENGLISH
IRCP200_UG_80x120 12-01-2010 14:53 Pagina 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek IR Control Pro System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek IR Control Pro System in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info