668721
83
Zoom out
Zoom in
Previous page
1/94
Next page
77
6-1. MIDI DATA DUMP
Data dump
1 Prog:
Data for the currently selected program
will be transmitted (1. Voice – 39. Lvl/
Pan page parameters, front panel but-
ton and knob settings.)
AllProg:
Data for all programs will be transmitted.
Global:
Global data will be transmitted (40. Glo-
bal-A – 46. Pedal/Sw page parameters,
foot pedal calibration setting, and
formant motion data.)
AllData:
All programs and global data will be
transmitted.
4
Press the blinking [6] button.
The data dump will be executed, and
then the R3 will return to the Play mode.
For more about the contents of pro-
gram data and global data, refer to the
explanations of what is saved in the
sections “Saving a program” and
“Saving Global and MIDI settings” in
“Saving (Writing)” (p.74).
For the size of the dumped data and
the time required for each, refer to the
table.
Reception procedure
Use the following procedure when you
want to load previously-saved data from
a connected MIDI data filer or computer
back into the R3, or to receive data from
another R3 unit.
1
Connect the R3’s MIDI IN connector to
the MIDI OUT connector of the device
that will transmit the MIDI dump data.
2
Set the MIDI channel of the transmitting
device to match the R3’s MIDI channel.
If you previously transmitted data to an
external MIDI device and want to re-
ceive it into the R3, be sure to set the
R3’s MIDI channel to the same channel
setting as when the data was originally
transmitted.
3
Set the 43. MIDIFilt page “SystemEx” to
Enable, turn the Shift function “PROTECT”
to off.
Data dump
“Data dump” is a function that transmits
program or global data in the form of MIDI
exclusive data, so that it can be saved on a
connected MIDI data filer or computer.
This can also be used to transmit data to
another R3 unit.
Do not touch the knobs or buttons of
the R3 while data is being transmitted
or received. Also, never turn the power
off during this operation.
Some USB-MIDI interface devices may
not be able to transmit/receive the
R3’s MIDI exclusive messages.
Transmission procedure
1
Connect the R3’s MIDI OUT connector
to the MIDI IN connector of a device that
is able to receive a MIDI data dump, and
set both devices to the same MIDI chan-
nel.
2
Hold down the [SHIFT] button and
press the PROGRAM SELECT [6] but-
ton.
The [6] button will blink. The main dis-
play will show the type of data dump
that will be transmitted.
3
Use the [PAGE] dial to select the type
of data dump that will be transmitted.
The size of the dumped data and the time required for each:
Data to dump
Data size (Bytes)
Time required
1 Prog 452 Less than one second
AllProg 57,856
approximately 3 minutes 15seconds
Global 192,144
approximately 2 minutes 10 seconds
AllData 250,000
approximately 5 minutes 30 seconds
4
Transmit the data from the MIDI data
filer or other device. For the transmis-
sion procedure, refer to the manual of
the device you are using.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg R3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg R3 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info