668721
92
Zoom out
Zoom in
Previous page
1/94
Next page
86
Trouble shooting
Before you suspect a malfunction, please check the following points.
Power does not turn on
Is the AC adaptor connected to an AC outlet? p.8
Is the [POWER/STANDBY] switch turned on (pressed inward)? p.10
No sound
If your powered monitor system or headphones connected to the correct
jack(s)? p.8
Is the connected monitor system powered-on, and is the volume raised?
Is the MASTER VOLUME knob set to a position where sound will be output?
p.10
Is the 42. MIDI page “Local”(knob [2]) setting turned ON? p.68
Were any volume-related parameters set to a value of 0? p.31, 37, 55, 59
Was the 8. Filt1-A page “Cutoff1” (knob [1]) set to 0? p.32
Was the 37. Filter page “E.F.Sens” set to Hold (FORMANT HOLD) while there
was no input to the [AUDIO INPUT 1] or [MIC] jack ? p.58
Can’t input sound
Is the input source connected to the [AUDIO INPUT 1] jack, the [MIC] jack, or
the [AUDIO INPUT 2] jack? p.10, 21, 34
If you are inputting to [MIC] jack, is the [MIC] switch set XLR p.10, 21, 34
If you are inputting to [AUDIO INPUT 1], is the [MIC] switch set REAR? p.
Is the [AUDIO INPUT1] or [AUDIO INPUT2] knob turned up? p.10, 21, 34
If using a vocoder program, have you connected the modulator audio source to
the [AUDIO INPUT 1] jack or to the [MIC] jack? p.10
Can’t edit
If you are unable to use the knobs [1][4] to edit the parameter value in the
performance edit, Edit mode may be active.
If you are unable to use the knobs [1][4] to edit the parameter value, Perfor-
mance Edit may be active. p.8, 12
If you are unable to edit timbre 2 of a synth program, has 1. Voice page “Mode”
been set to Layer, Split, or Multi? p.23
If you are unable to use the knobs [1][4] to edit timbre 1 or 2 of a synth program,
is the TIMBRE SELECT [TIMBRE 1] or [TIMBRE 2] button blink for the timbre
you want to edit? p.21
If you are unable to use the knobs [1][4] to edit vocoder parameters, is the
[VOCODER] button blink for the vocoder you want to edit? p.21
If the changes you made to a program or to the global settings have not been
remembered, did you turn the power off before executing the Write operation? In
the case of a program, your edits will also be lost if you select a different program.
Execute the Write operation to save your edits before you switch programs or turn
off the power. p.74
Can't write programs or global settings
Is Shift function “PROTECT” turned Off? p.78
If an edited program or edited GLOBAL, MIDI settings you thought you had
saved have not actually been saved, did you select “Global” when you attempted
to save the program, or “Program when you attempted to save the global data?
p.74
Arpeggiator will not start
Is the arpeggiator turned on (ON/OFF button lit)? p.15
Is the 42. MIDI page “Clock” (knob [4]) setting correct? p.68
No response to MIDI messages sent from an external device
Is the MIDI cable or USB cable connected correctly? p.65
Does the MIDI channel of the data transmitted from the external MIDI device
match the MIDI channel of the R3 p.65
Does not respond correctly to MIDI messages sent from an external device
Is the 43. MIDIFilt page parameters for that type of MIDI message set to Enable?
p.70
Transpose, velocity curve, and arpeggiator data is not recognized correctly
Is 40. Global-A page “Position” (knob [4]) set appropriately? p.62
Can't control two timbres on separate MIDI channels
The R3 uses only one MIDI channel to transmit and receive when 1. Voice page
“Mode” (knob [1]) is set to Single, Layer, or Split. You can use two MIDI channels
to play the two timbres independently only when 1. Voice page “Mode” (knob [1])
is set to Multi.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg R3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg R3 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info