683161

Kenwood TS-890S Manual

114
Zoom out
Zoom in
Previous page
1/196
Next page
Registering Operating Frequency Data to a Memory
Channel
The steps to register the frequency and mode to the memory
channel are as follows.
•
To register a split channel, press [SPLIT] to switch to the split
mode and operate accordingly.
1 Configure the frequency and mode to register.
2 Press F7 [M.LIST] to display the Memory Channel
List screen.
3
Press [ M.IN].
4
Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH]
control to select the memory channel for
registering the operating data.
•
Choose a memory channel from 00 to 99 or E0 to E9.
5
Press [ M.IN] or F4 [M.IN] to register the operating
data.
•
Pressing F1 [CANCEL] or [ESC] exits the Memory Channel
List screen without registering the operating data to the
memory channel.
Configuring the Operating Data through Direct
Frequency Entry
The numeric keypad can be used to register a frequency to a
memory channel or make changes to an operating data that is
already registered to a memory channel.
This is handy for adjusting the frequency to a station with a fixed
frequency.
1 Turn the [MULTI/CH] control to select the memory
channel (00 to 99 or E0 to E9) for registering the
operating data.
2 Press [ENT] to enable use of the numeric keypad.
•
The frequency entry mode starts up in the corresponding
band with all the frequency digits appearing as “-”.
•
To change the operating mode, press the mode key.
.
3 Key in a frequency value using the numeric keypad.
•
“-” changes into a numeric value when a numeric key is pressed
and a value can be input starting from the highest-order digit.
•
To enter 1.82 MHz, press [0/50], [1/1.8], [8/24] followed by
[2/3.5], and press [ENT] when input is complete.
•
To enter a frequency lower than 6 MHz for K type
transceivers, start by keying in a “0”.
•
To enter a frequency lower than 8 MHz for E type
transceivers, start by keying in a “0”.
•
Pressing [CLR] clears the input and exits the frequency
entry mode.
4 Press [ENT] to register the operating data.
The operating data is now registered to the memory channel
selected in step 2.
Memory Channel Mode
An operating data can be called up from a memory channel for
transmission or reception. Operating data such as the TX and RX
frequencies, mode and tone can be changed temporarily.
Operating in the Memory Channel Mode
Follow the steps below to call up the operating data of a memory
channel. Operating data that is registered in the memory channel
selected on the memory channel list is called up.
1 Pressing [M/V] in the VFO mode to switch to the
memory channel mode.
The selected band switches to the operating data that is
registered in the memory channel on the memory channel list,
and the memory channel number that is used is displayed on
the screen.
.
2 Press [UP] or [DOWN] on the microphone or turn the
[MULTI/CH] control to switch to the target memory
channel.
3 Pressing [M/V] again exits the memory channel
mode.
The transceiver returns to the VFO mode.
Direct Entry of a Memory Channel Number
A memory channel number can be selected by pressing the
corresponding number on the numeric keypad.
1 Enter the tens digit of the memory channel using the
numeric keypad.
•
The tens digit of the channel number is being entered for the
selected band while the ones digit appears as “-”.
2 Enter the ones digit of the memory channel using
the numeric keypad.
•
The operating data corresponding to the entered number is
called up and the channel number entry mode ends.
•
Pressing [CLR] clears the input and exits the channel
number entry mode.
9 MEMORY CHANNELS
9-2
… 114 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info