Manual Inverto IDLV-5000P (page 9 of 16) (English)

509864

Zoom out

Zoom in

1/16

Multicast IP Addr:• Enter the IP address of the multicast stream for the transport stream over IP.

Multicase UDP Port:

• Enter the UDP port number of the TS over IP stream.

Protocol: • select the protocol for multicast: UDP or RTP.

Output Smoothing:• set the quality of TS which comes from the TS/IP input.

Auto:• the bit rate is variable.

Disable:• the unit let the TS pass by.

Fixed Rate:• the bit rate is xed.

TS Bit Rate:• set the bit rate of the TS comes from the TS/IP input. The setting is only valid when the output

smoothing is congured as Fixed Rate.

5.2 OUTPUTS MENU

Under Outputs Menu, you can monitor and congure the parameters of the CI, AV decoder, ASI out, ASI2/SDI

out, Mux (A), BISS, SDI out and TS over IP output (B).

Note:

(A) The Mux menu is showed only if the functional block is enabled. Refer to section ‘Optional Function’.

(B) The Ethernet menu is showed only if the IP streaming in/out board is installed and the TS/IP streaming board

is set to “IP Out”. Refer to section ‘Optional Function’.

5.2.1 BISS Menu

It includes Biss Mode, Biss 1 Setup and Biss E Setup

Biss Mode: Set Biss mode, can select OFF, Biss E or Biss 1

Biss 1 Setup: set Biss 1, password is required

Biss E Setup: set Biss E, ID number and password are required

5.2.2 CI Menu

There are two PCMCIA slots for inserting CAM for de-encrypting program from the input signal.

Before setting CI, ensure the signal from ASI input is locked or the Tuner locks on the correct Transponder (this

depends on in which signal the encrypted program carried). The ‘Tuner Lock’ LED will ‘on’ in green.

There are 3 submenus: ‘CI Source’, ‘Setup’ and ‘CAM name’ which allow you to set or select the parameters of

the CI.

1. CI Source: press the <ENTER> key, then use <UP> or <DOWN > key select Tuner or ASI1 input or ASI2

input or TS/IP input (only when the TS/IP is set “IP In”, refer section 5.2.7 for details) to set the signal source of

descrambling, press <ENTER> key to save or press <EXIT> key to scrap.

2. Setup: under this sub menu, you can see all program names from the source of CI that was set in ‘CI Source’

previously. All free programs are marked with ‘Free’ in the rst row.

To select which program to be de-encrypted, press the <UP> or <DOWN>key to roll up and down the program

names and press <ENTER> key to change the status of the corresponding program (only encrypted program

could be selected). Three different statuses could be set:

Slot 1 (de-encrypted with upper CAM inserted)

Slot 2 (de-encrypted with lower CAM inserted)

Bypass (no de-encryption).

The status will be shown in the rst row on the LCD display. Conrm this setup when leaving this sub menu,

press <ENTER>key to save or press <EXIT>-key to scrap.

The de-encrypted program could be delivered to other functional blocks, like A/V decoder, ASI1, ASI2, SDI, Mux

and TS/IP output (refer to section 5.2.3~5.2.8 for more).

3. CAM name: under this sub menu, you can see the names of CAM modules.

Outputs

Decoder ASI1 ASI2 SDI Ethernet MuxBISS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-5000P in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inverto IDLV-5000P Manual

Product: