509864
8
Zoom out
Zoom in
Previous page
1/16
Next page
En
7
5.1 INPUTS MENU
There are four options: Status, DVB-S2, RSSI and Ethernet (optional):
5.1.1 Status Menu
It contains four options, ASI1, ASI2, TUNER and IP IN, to show the status of signal input:
ASI1:
• When signal from ASI1 input port is locked, it will display package format and code rate; if signal is
not locked, it will show Unlock.
ASI2:• When signal from ASI2 input port is locked, it will display package format and code rate; if signal is
not locked, it will show Unlock.
TUNER:• When signal from tuner input port is locked, it will display package format and code rate; if signal
is not locked, it will show Unlock.
IP IN: • When signal from IP input port is locked, it will display package format and code rate; if signal is not
locked, it will show Unlock.
Note: this option only appears when set the External Function as “IP IN”. Please refer to section ‘Optional
Function’ for setting method.
5.1.2 DVB-S2 Menu
There are 6 options to set DVB-S2 parameters. After signal is locked, the TUNER LOCK indicator on front panel
will turn green.
LNB Frequency:
• Input LNB frequency
Satellite Frequency:• Input downstream frequency of satellite
Symbol Rate:• Input symbol rate of satellite
LNB Voltage:• select the correct LNB voltage output of the F-connector: Off, 13 V, 18 V. <A>
LNB 22KHz: • activate the LNB 22 kHz control signal to the LNB: On or Off. <B>
DISQEC: • Can select OFF/Port A/Port B/Port C/Port D
Note: please contact the local satellite operator for the satellite frequency and symbol rate.
<A> Normally, 13V switches the LNB to receive Vertical/Left hand polarization while 18V receive Horizontal/Right
hand.
<B> Normally, 22KHz control signal switches the LNB to receive high band if any.
5.1.3 RSSI
There are two options to show the quality of receiving DVB-S2 signal.
5.1.4 Ethernet Menu
Note: The Ethernet menu is showed only if the IP streaming in/out board is installed and the TS/IP streaming
board is set to “IP IN”. Refer to section ‘Optional Function’.
The Ethernet connector is for receiving transport stream over IP. The Ethernet connector has user-congurable
IP address, network mask and default gateway. These must be set to appropriate values for the network over
which the transport stream over IP is received.
Stream IP Addr:
• Enter the IP address for streaming IP input of the unit.
Stream Netmask:• Enter the network sub mask for the subnet to which the unit is connected for IP
streaming trafc.
Stream Gateway:• Set the gateway for the network to which the unit is connected for IP streaming trafc.
Stream Mac Address:• factory-set MAC addresses are guaranteed to be unique. Therefore you cannot
congure the address.
Inputs
Status
DVB-S2
RSSI
Ethernet
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDLV-5000P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-5000P in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info