509864
6
Zoom out
Zoom in
Previous page
1/16
Next page
En
5
3.1 INSPECTION
Open the packaging box, check if all accessories are in the box according to the packing list, and if the device
has any visible damage, please contact the agent.
3.2 OPERATING VOLTAGE
Do not connect AC power until you have veried that the line voltage is correct and the proper fuses are
installed. The device’s power supply is tted with a wide-ranging power supply. It is suitable for supply voltages
of 100-240 Vac -10% +6% at 50/60 Hz nominal. Be sure the supply voltage is within the specied range.
POWER REQUIREMENT
Input voltage 90-250 Vrms auto select
Frequency 47 to 63 Hz
Power 50 VA max. / 30 VA typical.
Current 110 V/0.27A or 240 V/0.125A typical
3.3 THE FUSES
The recognized recommended fuses are size 5 by 20 mm, rate T 2.0A, 250 V (UL and IEC approved).
The line fuse is housed in a small container besides the power connector on the rear panel. To check the fuse,
insert the tip of a screwdriver in the slot at the middle of the container and pry gently to extend the fuse where
there is a little tap and pull out the fuse gently. The fuse is attached to the line module and cannot be removed.
3.4 CONNECTING UP THE DEVICE
Always use the specied cables supplied for signal integrity and compliance with EMC requirements.
The rear panel is directly related to the input and output options tted. Below gure shows a typical rear panel.
MANAGEMENT
1. LAN port for software update
ASI OUT22. Group2 ASI output port (one for back-up)
ASI OUT13. Group1 ASI output port (one for back-up)
ASI2 IN4. ASI2 input port
SDI25. SDI2 output port
SDI16. SDI1 output port
HDMI7. HDMI output port
CVBS8. CVBS BNC output port
CVBS9. CVBS RCA output port
L-Audio-R210. Group2 RCA audio output port
AUDIO211. AES/EBU and Balance Audio output port1 (need to use the RS232-to-XRL converting
cable in accessories)
GND12. Grounding terminal
Power Socket13. AC 90~250V 50-60Hz input
Switch14. Power switch
TS/IP IP15. input/output port
RS-23216. serial port for printing information
ASI1 IN17. ASI1 input port
YPbPr18. YPbPr output port
3. Installation
1 2 3 4 5 6 7 8 9 1 0 1 1 12 13 14
15 16 17 18 19 20 21 22
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDLV-5000P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-5000P in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info