509864

Inverto IDLV-5000P Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
10
5.2.4 ASI1
You can congure the settings of ASI1 in this menu.
ASI1 Source: Press the <ENTER> key and use the <UP> or <DOWN> key to roll up or down to select the signal
source of ASI output, there are 5 type of signal source optional:
CI De-encrypted:
1. the de-encrypted transport stream from CI functional block will be delivered to the ASI
output port on the back panel.
TUNER:2. the transport stream from Tuner block will be delivered to the ASI output port on the back panel.
ASI1 Input:3. the transport stream comes from ASI1 input port will be delivered to the ASI1 output port on
the back panel.
ASI2 Input:4. the transport stream comes from ASI2 input port will be delivered to the ASI2 output port on
the back panel.
Mux TS: 5. the transport stream comes from internal Mux functional block will be delivered to the ASI output
port on the back panel.
Note: The Mux TS is valid only when the Mux function block is enabled and turned on. Refer to section ‘Mux’
and section ‘Optional Function’ for how to set the Mux function block.
Press <ENTER> key to save or press <EXIT> key to scrap. A few seconds after the source being selected, the
TS will be delivered to the ASI output port on the back panel.
5.2.5 ASI2
The same conguration method like section of ‘ASI1’
5.2.6 SDI
You can congure the settings of SDI output in this menu.
Audio PID:
• press the <UP> <DOWN> keys to choose the audio PID from 1~4.
Embed Audios:
• there are 4 options: none, one&two, two, and one.
SDI Output Mode:
• congure output mode HD-SDI or SD-SDI
SDI H Offset:
• the range is 0~999
5.2.7 Mux
Note: this Mux menu is showed only when the Mux function block is enabled and turned on. And the Mux is
alternative (refer to section ‘Optional Function’ for how to turn on and set the Mux function block).
Mux Switch: • the internal multiplexer could be switched On/Off. The default value is ‘off’. To activate the
re-Multiplexing function, you should turn on this Mux functional block.
Bit Rate:• should be set to a specied value that doesn’t exceed the Maximum physical limit of the output
medium. For example, to deliver the multiplexed TS to an 8MHz DVB 256QAM modulator, it should not
exceed 55000Kb/s, otherwise overow occurs.
TS ID:• you can congure the TS ID to mark the multiplexed TS. Default value is 1.
Program List:• press the <ENTER> key to enter ‘Mux List’ sub-menu.
It shows all programs detected by IDLV-5000P. The programs could be come from ASI input, Tuner, TS/IP •
input or the internal CI de-encryption block. Use <UP> <DOWN> keys to roll up the program names, and
use <LEFT> <RIGHT> keys to switch among input sources, where a number in front of the program name
indicates the input source: 0-xxxxx displays the program name, which comes from ASI input.
1-xxxxx displays the program name, which comes from TUNER input.
2-xxxxx displays the program name, which comes from TS/IP input
3-xxxxx displays the program name which comes from the CI.
4-xxxxx displays the program name, which comes from ASI2 input.
5-xxxxx displays the program name, which comes from BISS De-encrypted
input.
On ‘Program List’ sub-menu, on the rst row, all encrypted programs are labeled with a ‘$’ sign.
All programs that are being selected to be re-multiplexed are labeled as ‘Pass’, otherwise, the un-selected
programs are labeled as ‘Fobrid’. Use <ENTER> key to selected or un-selected the program being shown.
When leaving the ‘Program List’ sub-menu, a new menu will be shown ‘Conrm changed?’ Press <ENTER> key
to validate all programs just be selected to be multiplexed or to scrap by pressing <EXIT> key.
After a few seconds, the multiplexed TS will be generated and delivered to the specied destination(s).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDLV-5000P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-5000P in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info