509864

Inverto IDLV-5000P Manual

13
Zoom out
Zoom in
Previous page
1/16
Next page
12
IPTV mode
Max Channels (<=6):
• you can congure the number of IPTV channel. The valid range goes from 0 to 6.
After the conguration, you can use <UP> <DOWN> keys to roll up and down between the channels. Each •
channel could be congured independently.
Channel x:• ‘x’ means the channel number. Press <ENTER> key to go down to the sub-menu.
There are 4 sub-menus:
x-Multicast IP:
1. Enter the IP address of the IP stream for the transport stream over IP output. You can also
congure the IP stream output mode in Multicast or Unicast by setting Multicast IP address.
x-Multicast Port:2. Enter the UDP port number of the TS over IP stream output.
x-Switch: 3. each channel could be switched On/Off independently. The default value is ‘off’. To activate the
channel, you should turn on.
x-Program:4. it shows all programs carried by the transport stream from the source selected. Press
<ENTER> key and use <UP> <DOWN> keys to roll up and down between the program names, where a
number in front of the program name indicates the input source:
0-xxxxx displays the program name, which comes from ASI input.
1-xxxxx displays the program name, which comes from TUNER input.
2-xxxxx displays the program name, which comes from TS/IP input
3-xxxxx displays the program name which comes from the CI.
4-xxxxx displays the program name, which comes from ASI2 input.
5-xxxxx displays the program name, which comes from BISS De-encrypted input.
6-xxxxx displays the program name, which comes from MUX TS.
All encrypted programs are labeled with a ‘$’ sign on the rst row. Press <ENTER> key to the program just be
selected to be delivered to the specied IPTV channel or to scrap by pressing <EXIT> key.
5.3 SYSTEM MENU
There are seven sub-menus:
Each IDLV-5000P has an IP address, a network sub mask and a gateway. These must be set to an appropriate
value for the network over which the unit can be accessed by the remote control system such as the HDMS.
IP Address:
• The IP address for the unit.
Network Mask:
• The network mask for the subnet to which the unit is connected.
Gateway:
• The gateway for the network to which this unit is connected.
5.3.2 Trap IP Address
The IDLV-5000P provides a Monitor Center IP address. You can set this to be the same IP address of the
Monitor Center, which is typically a PC in order to allow the device to send messages to the monitor center.
5.3.3 Unit Name
The IDLV-5000P allows you to edit the unit name which is displayed on the front panel LCD. Default name is
‘Digital TV Processor”. The unit name should not be longer than 20 characters in ASCII format.
5.3.4 Properties
Version:
• show software version of this device
MAC Address:• Factory-set MAC address which is guaranteed to be unique. You cannot congure this
address.
Linux OS version:• show Linux OS version
ARM SW version:• show ARM software version
System
Trap IP
Addr
Local
Setup
Unit
Name
Properties
Factory
Settings
Optional
Function
Machine
Type
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDLV-5000P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-5000P in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info