627057

Huvema CRDM 3050 X 2000 TOPLINE Manual

16
Zoom out
Zoom in
Previous page
1/36
Next page
16
7.5 maschIne eIn- und ausschalten
7.5.1 maschIne eInschalten
• Hauptschalter in Stellung „ON“ (EIN) stellen.
• Betriebsschalter einschalten (ON).
7.5.2 maschIne ausschalten
• Hauptschalter auf die Position OFF (AUS) stellen.
• Betriebsschalter ausschalten (OFF).
Bei einem Notfall den Not-Aus-Schalter drücken, um die Spannungsversorgung zu unterbrechen.
Den Not-Aus-Schalter jedoch nicht als normalen Bedientaster für eine Unterbrechung des normalen
Maschinenbetriebs verwenden!
7.6 arbeItsbeleuchtung
• Arbeitsbeleuchtung einschalten: Schalter für Arbeitsbeleuchtung einschalten (Stellung ON).
• Arbeitsbeleuchtung ausschalten: Schalter für Arbeitsbeleuchtung ausschalten (Stellung OFF).
7.7 schneIdflüssIgkeIten
• Schneidflüssigkeitszufuhr einschalten: Schalter für Schneidflüssigkeitszufuhr einschalten (Stellung ON).
• Schneidflüssigkeitszufuhr ausschalten: Schalter für Schneidflüssigkeitszufuhr ausschalten (Stellung OFF).
7.8 hochfahren des auslegers
Zum Heben des Auslegers den 4-Pos.-Schalter (1) auf Stellung „ARM UP“ stellen. Zum Senken des Auslegers
den 4-Pos.-Schalter (1) auf Stellung „ARM DOWN“ stellen. Den 4-Pos.-Schalter nach Erreichen der gewünschten
Position in die Mittelstellung stellen.
Beim Hochfahren des Auslegers wird die Klemmvorrichtung automatisch gelöst. Wird der 4-Pos.-
Schalter wieder in die Mittelstellung gestellt, dann wird die Klemmvorrichtung automatisch
geklemmt.
5-14
5.6 Work light
Turn on the work light. Switch the work light to ”ON”
position.
Turn off the work light. Switch the work light to ”OFF”
position.
5.7 Cutting fluids
Turn on the cutting fluids. Switch the cutting fluids to ”ON” position.
Turn off the cutting
fluids.
Switch the cutting fluids to ”OFF” position.
5.8 Elevating the arm .
Diagra
ms
1. Cross Switch.
Descrip
tion
For TPR-1230,TPR-1230H
(Type I)
For TPR-1230,TPR-1230H
(Type II)
For TPR-1600H, TPR-2000H
Steps
Turn the cross switch to “ARM UP” if
y
ou want to elevate it up, Turn the cross switch
to “ARM DOWN” if you want to elevate it down. Turn the cross switch to the middle
after the Arm reaches the required position.
Precaution
When the Arm is elevating, the clamping device will release itself automatically. When the
cross switch is turned to the middle, the clamping device will tighten itself automatically.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema CRDM 3050 X 2000 TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema CRDM 3050 X 2000 TOPLINE in the language / languages: German as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info