627057

Huvema CRDM 3050 X 2000 TOPLINE Manual

15
Zoom out
Zoom in
Previous page
1/36
Next page
15
7.4 bohrkopfklemmung bedIenen
1 Hebel zum Entriegeln des Bohrwerkzeugs
2 Vorschubhebel
3 Bohrspindel
7.4.1 bohrwerkzeug freIgeben
Schritt 1 Schritt 2 Schritt 3
• Schritt 1: An die linke Maschinenseite stellen.
• Schritt 2: Mit der rechten Hand den Vorschubhebel ergreifen und Bohrspindel zur äußersten oberen Position
verfahren.
• Schritt 3: Mit der linken Hand den Auslösehebel nach unten drücken.
Schritt 4
Schritt 4: Mit der linken Hand das Bohrwerkzeug dauerhaft umfassen und den Vorschubhebel entgegen den UZS
drehen, bis das Bohrwerkzeug sich löst.
7.4.2 aufnahmekegel und bohrfutter zusammensetzen
• Bohrwerkzeug entnehmen bzw. Spindelgetriebe bis zur äußersten Position anheben.
• Hauptschalter ausschalten.
• Schutzhandschuhe anziehen.
• Unter das Bohrwerkzeug und das Bohrfutter ein dickes Holzbrett legen.
• Den Vorschubhebel in UZS drehen und die Bohrspindel ca. 150 bis 200 mm absenken. Siehe Abb. a.
• Spindelwelle drehen, bis beide Öffnungen eine Flucht bilden. Anschließend den Bohrer hineindrücken, der
dann geklemmt wird (siehe Abb. b).
• Bohrer mit Spannseite nach oben positionieren (siehe Abb. d)
• Bohrer mit der Spannseite in die Aufnahme führen (Abb. b).
• Vorschubhebel in UZS drehen. Bohrspindel absenken, bis der Bohrer und das Unterende des Bohrfutters
Kontakt zum Holzbrett besitzen. Dabei etwas Kraft aufwenden, bis der Bohrer sicher festsitzt und nicht mehr
herausfällt.
Der Abstand zwischen dem Holzbrett, dem Bohrer und dem Bohrfutterende beträgt ca. 30 mm.
5-12
The way to use the releasing taper handle head and clamping head follows as:
（
only applicable for TPR-1600H /TPR-2000H）
1 The lever for releasing the drilling bit.
2 The feeding lever
3 The spindle
To dismantle as follows：
Step 1. Stand at the left side
of the machine.
Step 2 Grasp the feeding lever
using right hand and
release the spindle to its
utmost position.
Step 3. Press down the bit
releasing lever using left
hand.
Step 4. Keep grasping the drilling bit using left hand and rotate the feeding
lever counter clockwise until the bit comes out.
Assemble the drill bit head and the drill bit clamp as the following:
a. Move away the drilling bit or lift the gearbox to the utmost point.
b. Power off.
c. Put on gloves.
d. Insert a thick wood plate into the underneath of the drill bit and the drill bit clamp.
e.
Rotate the feed trip lever clockwise and have the spindle descend about
150 to 200 mm. As fig. a.
f.
Rotate the revolving shaft from the bushing till that thing behind the machine is visible from the
hole of releasing drill bit, as fig. b.
g. Place the drill bit clamp end up, as fig. d.
h.
Place the drill bit and its clamp end into the revolving shaft and have the drill shaft end inserted
into the hole for releasing the drill bit, as fig. b.
i.
Rotate the feed trip lever counter clockwise. Make the spindle descend till the drill bit and the
bottom end of the drill bit clamp head contact the wood plate. Apply a little bit force and complete
it by confirming that the drill bit won’t fall.
Precaution：
The distance between the thick wood plate, drill bit and the end of the drill bit clamp is about 30
mm.
5-12
The way to use the releasing taper handle head and clamping head follows as:
（
only applicable for TPR-1600H /TPR-2000H）
1 The lever for releasing the drilling bit.
2 The feeding lever
3 The spindle
To dismantle as follows：
Step 1. Stand at the left side
of the machine.
Step 2 Grasp the feeding lever
using right hand and
release the spindle to its
utmost position.
Step 3. Press down the bit
releasing lever using left
hand.
Step 4. Keep grasping the drilling bit using left hand and rotate the feeding
lever counter clockwise until the bit comes out.
Assemble the drill bit head and the drill bit clamp as the following:
a. Move away the drilling bit or lift the gearbox to the utmost point.
b. Power off.
c. Put on gloves.
d. Insert a thick wood plate into the underneath of the drill bit and the drill bit clamp.
e.
Rotate the feed trip lever clockwise and have the spindle descend about
150 to 200 mm. As fig. a.
f.
Rotate the revolving shaft from the bushing till that thing behind the machine is visible from the
hole of releasing drill bit, as fig. b.
g. Place the drill bit clamp end up, as fig. d.
h.
Place the drill bit and its clamp end into the revolving shaft and have the drill shaft end inserted
into the hole for releasing the drill bit, as fig. b.
i.
Rotate the feed trip lever counter clockwise. Make the spindle descend till the drill bit and the
bottom end of the drill bit clamp head contact the wood plate. Apply a little bit force and complete
it by confirming that the drill bit won’t fall.
Precaution：
The distance between the thick wood plate, drill bit and the end of the drill bit clamp is about 30
mm.
5-12
The way to use the releasing taper handle head and clamping head follows as:
（
only applicable for TPR-1600H /TPR-2000H）
1 The lever for releasing the drilling bit.
2 The feeding lever
3 The spindle
To dismantle as follows：
Step 1. Stand at the left side
of the machine.
Step 2 Grasp the feeding lever
using right hand and
release the spindle to its
utmost position.
Step 3. Press down the bit
releasing lever using left
hand.
Step 4. Keep grasping the drilling bit using left hand and rotate the feeding
lever counter clockwise until the bit comes out.
Assemble the drill bit head and the drill bit clamp as the following:
a. Move away the drilling bit or lift the gearbox to the utmost point.
b. Power off.
c. Put on gloves.
d. Insert a thick wood plate into the underneath of the drill bit and the drill bit clamp.
e.
Rotate the feed trip lever clockwise and have the spindle descend about
150 to 200 mm. As fig. a.
f.
Rotate the revolving shaft from the bushing till that thing behind the machine is visible from the
hole of releasing drill bit, as fig. b.
g. Place the drill bit clamp end up, as fig. d.
h.
Place the drill bit and its clamp end into the revolving shaft and have the drill shaft end inserted
into the hole for releasing the drill bit, as fig. b.
i.
Rotate the feed trip lever counter clockwise. Make the spindle descend till the drill bit and the
bottom end of the drill bit clamp head contact the wood plate. Apply a little bit force and complete
it by confirming that the drill bit won’t fall.
Precaution：
The distance between the thick wood plate, drill bit and the end of the drill bit clamp is about 30
mm.
5-12
The way to use the releasing taper handle head and clamping head follows as:
（
only applicable for TPR-1600H /TPR-2000H）
1 The lever for releasing the drilling bit.
2 The feeding lever
3 The spindle
To dismantle as follows：
Step 1. Stand at the left side
of the machine.
Step 2 Grasp the feeding lever
using right hand and
release the spindle to its
utmost position.
Step 3. Press down the bit
releasing lever using left
hand.
Step 4. Keep grasping the drilling bit using left hand and rotate the feeding
lever counter clockwise until the bit comes out.
Assemble the drill bit head and the drill bit clamp as the following:
a. Move away the drilling bit or lift the gearbox to the utmost point.
b. Power off.
c. Put on gloves.
d. Insert a thick wood plate into the underneath of the drill bit and the drill bit clamp.
e.
Rotate the feed trip lever clockwise and have the spindle descend about
150 to 200 mm. As fig. a.
f.
Rotate the revolving shaft from the bushing till that thing behind the machine is visible from the
hole of releasing drill bit, as fig. b.
g. Place the drill bit clamp end up, as fig. d.
h.
Place the drill bit and its clamp end into the revolving shaft and have the drill shaft end inserted
into the hole for releasing the drill bit, as fig. b.
i.
Rotate the feed trip lever counter clockwise. Make the spindle descend till the drill bit and the
bottom end of the drill bit clamp head contact the wood plate. Apply a little bit force and complete
it by confirming that the drill bit won’t fall.
Precaution：
The distance between the thick wood plate, drill bit and the end of the drill bit clamp is about 30
mm.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema CRDM 3050 X 2000 TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema CRDM 3050 X 2000 TOPLINE in the language / languages: German as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info