627057

Huvema CRDM 3050 X 2000 TOPLINE Manual

14
Zoom out
Zoom in
Previous page
1/36
Next page
14
7.3 elektrIsche bedIenelemente
Frontansicht Rückansicht
7.3.1 beschreIbung der schalter
1. Not-Aus-Schalter Dient dem unmittelbaren Abschalten der Maschine in einem Notfall.
Zum Entriegeln den Schalter ziehen.
2. Schalter für Zugabe von
Schneidflüssigkeit
Für die Schmierung des Werkzeugs während der Bearbeitung, um
die dabei entstehenden Temperaturen zu reduzieren, die einen
erhöhten Verschleiß verursachen. Ein = Schmierung starten, Aus =
Schmierung ausschalten. Der Schneidflüssigkeitsstrom wird über
den Schneidflüssigkeitsregulierer beeinflusst.
3. Betriebsschalter (mit Meldeleuchte) Anzeige leuchtet, wenn Versorgungsspannung vorhanden und die
Maschine eingeschaltet ist.
4. Schalter für Klemmung lösen Löst die Klemmung von Ausleger und Spindelgetriebe, damit dieses
in allen drei Achsen bewegt werden kann.
5. Schalter für Klemmung aktivieren Dient der Klemmung von Ausleger und Spindelgetriebe. Mit
diesem Schalter werden Spindelgetriebe und Ausleger nach deren
Positionierung geklemmt, um die Position zu erhalten.
6. Amperemeter Dient der Anzeige der Bearbeitungsleistung (normal / zu hoch)
7. 4-Pos.-Schalter Dient der vertikalen Bewegung der Spindel und Vorwahl der
Spindeldrehrichtung. Ist mit 4 Symbolen beschriftet. Schalterstellung
„SPDL. FOR.“: Bohrspindel dreht in UZS. Schalterstellung „SPDF.
REV.“: Bohrspindel dreht entgegen UZS. Schalterstellung „ARM UP“:
Ausleger wird angehoben. Schalterstellung „ARM DOWN“: Ausleger
wird abgesenkt.
8. Schalter für die Arbeitsleuchte Dient der Ausleuchtung des Arbeitsbereiches bei ungenügender
Beleuchtung.
5-8
5.2.2 (For TPR-1600H/ TPR-2000H)
The front view of the machine The rear view of the machine
Description for Switches.
1. Emergent stop
It is pressed to stop the machine when at processing and emergence occurs.
Pull it again for back to release the stop.
2.
The cutting fluids
switch
It is a switch to start on or off the lubrication when at boring, where the
boring or shearing causes high temperature, making the drilling bit easy to
wear. The lubrication can reduce the temperature and lengthen the life of the
drilling bit. Turn on to start and off to stop the lubrication. The floating
capacity is decided by another knob called the cutting fluids adjusting knob.
3.
Power switch
(light attached)
When external power and the machine is on, the main power light will be on,
to indicate to the operator that the power is on.
4. Release switch
It is to release the clamping of the Arm and the Gearbox so that the Gearbox
can elevate, move for or backwards, left or rightwards.
5. Clamping switch
It is used to clamp the Arm and the Gearbox. After the Gearbox, moveable up
and down, for and backwards, left and rightwards, is positioned, You can use
this switch to fasten the above mechanisms in positions.
6.
Electric current
meter
It is for operator’s understanding whether the working situation is normal.
7. Cross switch
It is to control the elevating and revolution. There are four sign on it. When
switched to “SPDL. FOR.”, the spindle revolves clockwise. When switched to
“SPDL.REV.”, it revolves counter clockwise. When switched to “ARM UP”,
the Arm lifts. When switched to “ARM DOWN”, the arm descends.
8. Work light switch It is used to improve lighting where illumination is not enough.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema CRDM 3050 X 2000 TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema CRDM 3050 X 2000 TOPLINE in the language / languages: German as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info