734469

Husqvarna ST 430T Manual

22
Zoom out
Zoom in
Previous page
1/200
Next page
To install the belt cover
1. Install the belt cover (B) on the frame (C) and tighten
the two screws (A).
C A
B
2. Install the discharge chute.
To adjust the drive belt tension
1. Remove the belt cover. See
To prepare for
replacement of the belts on page 21
.
2. Loosen the idler pulley nut (A).
3. Move the idler pulley (B) in the direction of the belt to
increase the belt tension. Move it away from the belt
to decrease the belt tension.
B
A
4. Tighten the idler pulley nut (A).
5. Press and then release the drive speed control lever.
If the drive belt has tension when the drive speed
control lever is released, move the idler pulley away
from the drive belt to release the belt tension.
6. Install the belt cover. See
To install the belt cover on
page 22
.
To remove the auger belt (for ST 424/427/430
only)
1. Remove the 5/16'' nut and the cable cover (E) from
the frame.
A
E
B
D
C
2. Remove the top 5/16'' bolts and the lower ¼'' bolts
(D) from the 2 sides of the frame. Do not discard the
bolts.
3. Loosen but do not remove the lower 5/16'' bolts (C)
on the 2 sides of the frame.
4. Remove the auger belt (B) from the engine pulley
(A).
5. Tilt the rear section down. The front section tilts
forward at the same time. The bottom bolt is a hinge
between the front and rear sections.
6. Put a wooden block below the hinge point to set the
product in the tilted position.
7. Move the auger brake arm and remove the auger
belt (B) from around the auger brake arm.
22 891 - 005 - 08.01.2020
… 22 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-st-430t

Reset search

  • PRI ZARAZENÍ ZPETNÉHO POJEZDU STROJ CUKÁ A NEJEDE KLIDNE Submitted on 16-1-2021 at 14:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 430T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 430T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info