Manual Husqvarna ST 430T (page 21 of 200) (English, German, Dutch, French, Italian, Spanish)

734469

Zoom out

Zoom in

1/200

WARNING: The belt replacement requires

separation of the product. While separating

the auger housing from the frame, it is

important that an assistant stands in the

operating position and holds the product

handles. Serious personal injury and/or

damage to the product could occur if the

product falls during the belt replacement

process.

To prepare for replacement of the belts

1. Remove the fuel from the fuel tank.

2. Loosen the lock nut (A) that secures the chute

rotator head (B) to the mounting bracket (C) to

remove the discharge chute.

3. Loosen the two screws (A) that secure the belt cover

(B) to the frame (C) and remove the belt cover.

C A

To remove the drive belt

1. Remove the auger belt (A). See

To remove the

auger belt (for ST 424/427/430 only) on page 22

2. Remove the 9/16 in. pulley bolt (B) and remove the

engine pulley (C) from the engine.

3. Remove the drive belt (D) from the lower pulley (E).

To install the drive belt

1. Put the drive belt onto the lower pulley (E).

Note: Make sure that the drive belt is put in the lower

pulley groove properly.

2. Put the drive belt in the groove of the engine pulley

(C).

3. Install the 9/16 in. pulley bolt (B) and attach the

engine pulley (C) on the engine. Tighten the pulley

bolt ( 41-47 Nm/30-35 Ft. Lbs).

4. Install the auger belt (A). See

To install the auger

belt on page 23

5. Operate all controls to make sure that the drive belt

is installed correctly and that all components move

correctly.

891 - 005 - 08.01.2020 21

PRI ZARAZENÍ ZPETNÉHO POJEZDU STROJ CUKÁ A NEJEDE KLIDNE Submitted on 16-1-2021 at 14:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 430T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna ST 430T Manual

Product: