Manual Husqvarna ST 430T (page 19 of 200) (English, German, Dutch, French, Italian, Spanish)

734469

Zoom out

Zoom in

1/200

Muffler

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Do not use the product if the muffler is missing or

defective. A defective muffler increases the noise level

and the risk of fire.

Examine the muffler regularly to make sure that it is

attached correctly and not damaged.

CAUTION: The muffler becomes very hot

during and after use and when the engine

operates at idle speed. Be careful near

flammable materials and/or fumes to prevent

fire.

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, see

Technical data on

page 29

• Replace the spark plug if it is necessary.

To inspect the augers and the scraper

bar

1. Before each use, inspect the augers and the scraper

bar for wear.

2. If the edge of the scraper bar is worn, reverse the

scraper bar. If the scraper bar has damages or is

worn on both edges, replace it.

3. If the edges of the augers are worn, contact an

authorized service center to replace them.

To replace the auger shear pins

The auger shear pins protect the product from damage.

The auger shear pins break if an object comes into the

moving parts.

CAUTION: Use only original equipment

shear pins supplied with the product.

1. If an auger shear pin breaks, stop the engine and

wait for the moving parts to stop.

2. Remove the ON/OFF key and disconnect the spark

plug cable.

3. Align the hole in the auger hub (B) with the hole in

the auger shaft (C) and install a new ¼ - 20 x 2

shear pin (A).

4. Install a ¼-20 locknut (D) on the shear pin and

tighten.

5. Put the ON/OFF key in the ignition and connect the

spark plug cable to the spark plug.

To replace the impeller shear pins

The impeller shear pins protect the product from

damage. The impeller shear pins break if an object

comes into the moving parts.

CAUTION: Use only original equipment

shear pins supplied with the product.

1. If an impeller shear pin breaks, stop the engine and

wait for the moving parts to stop.

2. Remove the ON/OFF key and disconnect the spark

plug cable.

3. Align the hole in the impeller hub (A) with the holes

in the impeller shaft (B) and install a new ¼-20 shear

pin (C).

891 - 005 - 08.01.2020 19

PRI ZARAZENÍ ZPETNÉHO POJEZDU STROJ CUKÁ A NEJEDE KLIDNE Submitted on 16-1-2021 at 14:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 430T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna ST 430T Manual

Product: