734469

Husqvarna ST 430T Manual

20
Zoom out
Zoom in
Previous page
1/200
Next page
4. Install a ¼-20 locknut (D) on the shear pin and
tighten.
B
C
A
D
5. Put the ON/OFF key in the ignition and connect the
spark plug cable to the spark plug.
To replace the fuse
The fuse holders are installed behind the battery cover.
A
B
C
D
• Replace the fuse for engine control unit (A) with a 5
A fuse.
• Replace the fuse for the starter solenoid (B) with a
20 A fuse.
• Replace the fuse for the LED and the heated grip (C)
with a 5 A fuse.
• Position (D) contains a backup 5 A fuse.
To examine the tires
• Keep the tires free of fuel, oil and chemicals to
prevent damage to the rubber.
• Keep the tires away from stumps, stones, ruts, sharp
objects and other objects which can cause damage
to the tires.
• Keep the tire pressure correct, see
Technical data
on page 29
.
To clear a clogged discharge chute
deflector
Do not unclog the discharge chute deflector before the
following operations are made.
1. Release the auger engagement and the drive
engagement at the same time.
2. Wait 10 seconds to make sure that the augers have
stopped.
3. Stop the product.
4. Use the tool for cleaning (at least 37 cm (15 in.) long,
included in some models) to remove the clog.
WARNING: Do not put your hands into
the discharge chute deflector or inside
the auger bucket.
To replace the scraper bar
1. Put the scraper bar (A) in a reversed position when it
is worn to the edge of the housing.
A
2. Replace the scraper bar if it is worn on both sides or
if it is damaged.
Drive belts
WARNING: The v-belts on your product are
of special construction and should be
replaced by original equipment manufacturer
(OEM) belts available from your nearest
service center. To use other belts than OEM
can cause personal injury or damage to the
product.
20 891 - 005 - 08.01.2020
… 20 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-st-430t

Reset search

  • PRI ZARAZENÍ ZPETNÉHO POJEZDU STROJ CUKÁ A NEJEDE KLIDNE Submitted on 16-1-2021 at 14:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 430T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 430T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info