Manual Hormann Supramatic 2 (page 39 of 46) (English)

459144

39

Zoom out

Zoom in

Previous page

1/46

Next page

68 04.2007 TR10A041-C RE

7.7 MENU 7 – behaviour during operation in the

CLOSE direction (see fig. 28 )

In this menu, the automatic belt relief, the braking

behaviour and the speed in the CLOSE end-of-travel

position can be influenced.

Note

After the menu changes, a learning cycle may have to be

carried out.

Display Function

Soft stop

long

short

Relief

automatic

long

Speed

slow

normal

Press the PRG button to return to normal operation

(menu 0).

7.8 MENU 8 – force limit during operation in the

OPEN direction (see fig. 29 )

In this menu, the sensitivity of the automatic force limit

for the opening cycle can be set (factory setting: para-

meter 4).

Note

Increasing the force value (parameter greater than 4) is only

possible if parameter 3 has been selected in menu J.

ATTENTION

Do not select an excessively high setting as

excessive force may cause damage to equip-

ment or injuries to persons.

For doors moving easily, a low value can be selected

when the sensitivity to obstructions is to be increased.

Press the PRG button to return to normal operation

(menu 0).

7.8.1 Checking the forces in the OPEN direction

When changing the settings in menu 8, the forces as

defined in EN 12453 in the OPEN direction must be

complied with, i.e. a subsequent check is absolutely

essential.

7.9 MENU 9 – behaviour during operation in the

OPEN direction (see fig. 30 )

In this menu, the automatic belt relief and the braking

behaviour in the OPEN end-of-travel position can be

influenced.

Note

After the menu changes, a learning cycle may have to be

carried out.

Display Function

Soft stop

extra long

long

short

Relief

automatic

short

Soft start from CLOSE end-of-travel position

short

long

Speed

slow

normal

fast

Force limit response

stop

short reverse

Note

- Parameters 0 and 6: these parameters are matched to

the characteristics of retractable up-and-over doors.

- Parameters A and b: these parameters only need to be

set when parameter 3 has been selected in menu J.

Otherwise, parameter A is active in this menu.

- Parameter b: if error 5 (force limit) occurs when the door

is opening, the door travels a short distance back (roughly

10 cm of carriage) in the opposite direction and then

stops.

Press the PRG button to return to normal operation

(menu 0).

ENGLISH

1

Avrei necessità di riprogrammare il mio SupraMatic P 2 nennlast 225 N. Submitted on 23-3-2023 at 18:59
Reply Report abuse
Tengo un supramatic E2 y quiero conectar una apertura por WiFi, quisiera saber a que conectores, va el modulo wifi Submitted on 28-9-2022 at 18:37
Reply Report abuse
With my previous house I was able to connect additional mains (LED) internal garage lighting that operated in unison with the lighting on the Supermatic. Am I able to do this with the new Supermatic, and what connections do I need to use. Thanks VM Submitted on 16-2-2022 at 16:29
Reply Report abuse
Hoe kan ik de garagepoort "ontkoppelen" van de ketting van de motorisatie om bij stroomuitval manueel te kunnen bedienen? Submitted on 10-5-2021 at 00:39
Reply Report abuse
Good morning,

We have a Hormann Supramatic E2. Very happy with it. This morning however, it closes fine but only opens about 40 cm. This from main button as remote control. Both have the same result. It will close without problem. We have unplugged it and replugged after a few minutes. The track appears to be clear and clean. There is a 5 in red appearing on main unit but I don't know if this is normal to be honest. Advice will be very welcome.
Mariet Procter Submitted on 7-1-2021 at 11:20
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Hormann Supramatic 2 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Supramatic 2 in the language / languages: English as an attachment in your email.

The manual is 7,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hormann Supramatic 2

Hormann Supramatic 2 Usermanual and installation guide - German - 56 pages

Hormann Supramatic 2 User Manual - Dutch - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info