816209

Hikoki CG18DA Manual

21
Zoom out
Zoom in
Previous page
1/380
Next page
English
21
○ Release the lever when you finish cutting and stop the
motor.
○ Take a posture that makes it easy to move.
[Using the semi-auto nylon head]
– Do not swing the pipe, but use the hips to move the
nylon head horizontally from left to right in an arc while
going forward and use the right side of the nylon head
for cutting grass. (Fig.20)
[Using the blade]
– Cut grass from right to left, using the left side of the
blade to cut. (Fig.21)
– Slightly tilting the blade to the left while cutting will pile
the cut grass to the left, making collection easy.
WARNING
○ Blade thrust may occur when the spinning blade
contacts a solid object in the critical area.
A dangerous reaction may occur causing the entire unit
and operator to be thrust violently. This reaction is
called blade thrust. As a result, the operator may lose
control of the unit which may cause serious or fatal
injury. Blade thrust is more likely to occur in areas
where it is difficult to see the material to be cut.
○ If cutting attachment should strike against stones or
other debris, stop the engine and make sure that the
attachment and related parts are undamaged.
NOTE
Excessively increasing rotation speed may cause
increased blade wear, vibration and noise. It will also
wear out the battery faster.
6. Carrying the tool
CAUTION
○ Remove the storage battery. (Fig.5)
○ Carry the tool holding with hands.
○ If the blade is installed, attach the included blade cover.
OPERATIONAL CAUTIONS
This tool incorporates a function to safeguard the electronic
components that control the main unit. If an overload
occurs during mowing—for example, if the cutting
attachment locks up or becomes clogged with vegetation—
the function will activate to stop the motor. If this happens,
the power switch (47 in Fig.22) will flash.
Check the signal status and take appropriate corrective
action. (Table3)
You can resume use after taking the following corrective
action. Take steps to reduce the load imposed on the motor
—for example, by reducing the cutting depth. Before
clearing vegetation from the cutting attachment, turn off the
power and remove the battery from the tool main unit.
Table3
Power lamp
flashing status Cause Corrective action
0.5s on/
0.5s off
(slow flashing)
The internal
temperature
exceeded the
preset limit. The
tool has stopped.
(The motor turns
off. The power will
shut down
automatically after
one minute.)
[Temperature
protection
function]
Turn off the power
and wait for the
device to cool.
You can resume
use once the
device
temperature has
fallen.
Power lamp
flashing status Cause Corrective action
0.1s on/
0.1s off
(rapid
flashing)
The tool
attachment load
exceeded the
preset limit. The
tool has stopped.
(The motor turns
off and the lamp
flashes for
10seconds.)
[Overload
protection
function]
Turn off the power
and remove the
battery. Resolve
the cause of the
overload.
You can resume
use after resolving
the overload
cause.
MAINTENANCE AND INSPECTION
WARNING
Pull out battery before doing any inspection or
maintenance.
Maintenance safety
○ Maintain the unit/machine according to recommended
procedures.
○ Use only genuine HiKOKI replacement parts as
recommended by the manufacturer.
WARNING
Improper maintenance could result in serious machine
damage or in serious personal injury.
1. Checking the condition of the cutting attachment
The cutting attachment should be checked regularly. If
worn or broken cutting attachment can slip or decrease
the efficiency of the motor and burn it out.
Replace worn cutting attachment with new ones.
CAUTION
If you use a cutting attachment of which point is worn or
broken, it will be dangerous. So replace it with a new
one.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
6. Gear case (Fig.26)
Check gear case or angle gear for grease level about
every 50hours of operation by removing the grease
filler plug on the side of gear case.
If no grease can be seen in the screw hole on the sides
of the gears, fill the gear case up to 3/4 full with quality
lithium based multipurpose grease (sold separately).
CAUTION
○ Make sure to remove any dirt or grit when attaching the
plug to its original position.
2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18
CG18DA(L)_C99750571_311_EU
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CG18DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CG18DA in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info