816209

Hikoki CG18DA Manual

19
Zoom out
Zoom in
Previous page
1/380
Next page
English
19
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 5 3
Charging 6 4
Remaining battery indicator 23 7
Charging a USB device from a
electrical outlet 24-a 7
Charging a USB device and battery
from a electrical outlet 24-b 7
How to recharge USB device 25 7
Selecting accessories — 372
ASSEMBLY PROCEDURES
WARNING
Pull out battery before doing any assembly.
1. Installing of handle (Loop handle type) (Fig.7)
Attach the handle to the main pipe with the angle
towards the grip side.
Adjust the location to the most comfortable position
before operation.
Make sure to securely attach the handle with the
2bolts.
NOTE
Install the loop handle between the arrow marks on the
handle location label.
2. Installing of guard
WARNING
If an incorrect or faulty guard is fitted, this may cause
serious personal injury.
CAUTION
The guard extension is equipped with the knife. Be
careful with handling it.
Align the guard with the cover bracket and secure it to the
main pipe, using the bolt and cover bracket. (Fig.8)
NOTE
○ The guard extension is already attached to the guard at
the time of purchase.
○ The cover bracket may come already mounted to the
gear case.
3. Installing the shoulder belt
WARNING
○ Be sure to attach the shoulder belt so that the brush
cutter can be carried correctly.
○ If you get the feeling the tool is not operating normally,
turn off the motor immediately, remove the quick-
release bracket of the shoulder belt and remove the
tool.
CAUTION
○ If you do not support the tool when you pull the quick-
release belt, it may fall causing injury or damage. Hold
the main pipe with one hand while you pull with the
other hand.
○ Make sure the quick-release function operates normally
before you start working.
○ Before attaching, check to confirm that the belt is not
cut, frayed, or damaged.
○ Check to confirm that the hook and hanger are neither
deformed nor damaged.
○ Once attached, press down on the main unit to confirm
that the hook does not detach easily and that the
shoulder belt is not loose.
○ Check to confirm that the quick release function
operates as it should.
(1) Place the shoulder belt on the shoulder as shown in
Fig.9 and engage it with the hanger on the tool. Adjust
the shoulder belt to suitable length.
NOTE
You may need to adjust the position of the hanger to
balance the unit. To do so, loosen bolt and adjust the
position of hanger. After adjusting as necessary, make
sure to securely tighten the bolt. (Fig.10)
(2) To remove the tool from the shoulder belt, support the
tool by holding the main pipe with one hand and use the
other hand to pull the quick-release belt as shown in
Fig.11 to free it from the bracket.
(3) To strap on the tool, insert the bracket in the hook and
insert the quick-release bracket over the hook and into
the wide opening of the bracket. (Fig.12)
Gently pull the shoulder belt to make sure that it is
properly attached.
4. Installation of cutting attachment
WARNING
○ Install the cutting attachment properly and securely as
instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause serious and/or fatal injury.
○ Always use genuine HiKOKI cutting attachments and
metal fittings.
[Installation of semi-auto nylon head]
WARNING
For HiKOKI heads, use only flexible, non-metallic line
recommended by the manufacturer. Never use wire or
wire ropes. They can break off and become a
dangerous projectile.
(1) Function
Automatically feeds more nylon cutting line when it is
tapped at low rpm (not greater than 4000 min-1).
2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18
CG18DA(L)_C99750571_311_EU
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CG18DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CG18DA in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info