816209

Hikoki CG18DA Manual

20
Zoom out
Zoom in
Previous page
1/380
Next page
English
20
Specifications
Code
No.
Type of
attaching
screw
Direction of
rotation
Size of
attaching
screw
381230
Female
screw Counter-
clockwise M10 x
P1.25-LH
Applicable nylon cord
The standard accessory nylon head can be used with lines
from Φ2.0mm (max. length 4m) up to Φ2.7mm (max.
length 2m).
CAUTION
○ The case must be securely attached to the cover.
○ Check the cover, case and other components for cracks
or other damage.
○ Check the case and button for wear. If the wear limit
mark on the case or the arrow mark on the button is no
longer visible or there is a hole in the bottom of the
button, change the nylon head immediately. (Fig.13)
○ The nylon head must be securely mounted to the unit’s
gear case.
○ If the nylon head does not feed cutting line properly,
check that the nylon line and all components are
properly installed. Contact HiKOKI Authorized Service
Centers if you need assistance.
(2) Installation (Fig.14)
A: Align the hex. bar wrench with the hole of the gear case
and with the groove of the cutter holder (A) and insert it
to stop the rotation of the blade.
B: Install nylon head on gear case of tool. The mounting
nut is left-hand-threaded. Turn clockwise to loosen/
counter-clockwise to tighten.
NOTE
Since the cutter holder cap is not used here, keep it for
when a metal blade is used, if so equipped.
(3) Adjusting line length
Set the speed as low as possible and tap the button on
the ground. The nylon line will be drawn out about
30mm with each tap. (Fig.15)
Also, you can extend the nylon line by hand but the
motor must be completely stopped. (Fig.16)
Adjust the nylon line to the proper length of 110–
140mm before each operation.
[Installing the cutting blade]
(1) Installation (Fig.17)
WARNING
○ When installing a cutting blade, make sure that there
are no cracks or any damage in it and that the cutting
edges are facing the correct direction.
○ Remove any surface grit from blade installation fittings
(cutter holder (A) (B), nut cover, nut). Failure to do so
may result in the loosening of nuts.
○ The protrusion of the cutter holder (A) may become
misaligned with the blade while tightening nut. Before
operation, make sure the blade has been properly
installed.
○ Rotate the blade by hand and make sure there is no
rocking or abnormal noise. Rocking may cause
abnormal vibrations or result in the loosening of nuts.
CAUTION
○ If your unit is equipped with protection cover under a
cutting blade, check the blade installation brackets for
wear or cracks before operation. If any damage or wear
is found, replace it, as it is an article of consumption.
○ You have to wear gloves when handling the cutting
blade.
NOTE
When installing cutter holder cap, be sure to set
concave side upward.
A: Align the hex. bar wrench with the hole of the gear case
and with the groove of the cutter holder (A) and insert it
to stop the rotation of the blade. Please note that the
cutter fixing bolt or nut has left-handed threads,
(clockwise to loosen/ counter-clockwise to tighten).
B: Tighten the fixing bolt or nut with the box wrench.
OPERATION
WARNING
○ Avoid using the tool continuously for long hours, and
take a break of at least 5 minutes after every 30 minutes
of working.
Being tired is the largest cause of accidents. Allow
enough time to work without rushing.
○ Do not operate the tool at night or under bad weather
conditions when visibility is poor.
○ Do not operate the tool when it is raining or right after it
has been raining.
○ Wear proper footwear to prevent slipping that could
cause you to lose your balance and fall.
○ Do not use the tool on steep slopes.
When cutting on slopes that are not so steep, cut by
moving towards the ridge.
○ Take care not to move the cutting attachment too close
to your feet.
○ Do not raise the cutting attachment above your knee
during cutting.
○ Do not use the tool where the cutting attachment may
come into contact with stones, tree and other obstacles.
○ A cutting attachment can injure while it continues to spin
after the motor is stopped. When the unit is turned off,
make sure the cutting attachment has stopped before
the unit is set down.
○ Do not use the tool within 15m of another person.
When you work with someone else, maintain a distance
of more than 15m.
1. Insert the battery.
2. Turn on the tool. (Fig.18)
○ Press the power switch on the handle, the power goes
on and the power lamp on the handle lights green.
○ Pressing the power switch a second time turns the
power off and the green lamp on the handle goes off.
○ While the lever is pulled, the power does not turn ON
when the power switch is pressed.
[Auto power off]
– When the power is turned on but the lever is not used
for 1minute, the tool is automatically turned off. To turn
the tool on again, press the power switch a second
time.
WARNING
Never leave the tool with the power on. This could result
in an accident.
3. Mode switch (Fig.18)
The tool is equipped with three modes:
“Power Mode” “Normal Mode” “Eco Mode”.
Each time the mode switch is pressed, the operation
mode changes.
The set mode remains set even if the power is turned
off.
4. Lever operation and brake (Fig.19)
To start rotation of the cutting attachment, with the
power turned on, pull the lever while pressing the lock
lever.
When you release the lever, the brake engages in 1–
3seconds, stopping rotation of the cutting attachment.
Make sure that the brake operates normally before
using the tool.
5. Cutting
○ Grip the handle, press the lock lever and pull the lever
to start cutting head rotation. (Fig.19)
2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18
CG18DA(L)_C99750571_311_EU
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CG18DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CG18DA in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info