816209

Hikoki CG18DA Manual

22
Zoom out
Zoom in
Previous page
1/380
Next page
English
22
○ Before attempting inspection or maintenance of the
gear case, make sure the case has cooled.
7. Semi-auto nylon head
Nylon line replacement
(1) Remove the case by firmly pushing inward the locking
tabs. After removing the case, take out the reel and
discard the remaining line. (Fig.27)
(2) Rotate the button in the direction of the button arrow
mark, and align the nylon line guide and the reel groove
in a straight line. (Fig.28)
(3) Starting from the nylon line guide, insert the nylon line in
the direction of the reel arrow mark and pass it through
the reel groove, then pull it out to the nylon line guide on
the opposite side.
Make the nylon line the same length on both ends.
(Fig.29)
(4) Rotate the button in the direction of the button arrow
mark, and wind the nylon line onto the reel.
The initial cutting line length should be approx.110–
140mm and should be equal on both sides. (Fig.30)
(5) Place the cover over the case so that the locking tabs
on the cover meet the locking holes of the case. Then
push the case securely until it clicks into place.
CAUTION
Ensure that the hooks are securely hooked onto the
latch in 2places.
If the area around the latch becomes clogged with dirt,
etc., it may not be able to lock securely, so clean it
periodically to remove dirt.
8. Blade (Fig.31)
WARNING
Wear protective gloves when handling or performing
maintenance on the blade.
○ Use a sharp blade. A dull blade is more likely to snag
and thrust. Replace the fastening nut if it is damaged
and hard to tighten.
○ When replacing blade, purchase one recommended by
HiKOKI, with a 25.4mm (one inch) fitting hole.
○ In the case of a 3tooth blade, it can be used on either
side.
○ Use the correct blade for the type of work.
○ When replacing blades, use appropriate tools.
○ When cutting edges become dull, re-sharpen or file as
shown in the illustration. Incorrect sharpening may
cause excessive vibration.
○ Discard blades that are bent, warped, cracked, broken
or damaged in any way.
NOTE
When sharpening blade it is important to maintain an
original shape of radius at the base of the tooth to avoid
cracking.
9. Storage
Store the power tool and battery in a place in which the
temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
significantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, significantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to five times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when the
battery is disassembled and modified (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling
instruction, to a HiKOKI Authorized Service Center.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level:
(Nylon head) 92dB(A)
(Blade) 91dB(A)
Measured A-weighted sound pressure level:
(Nylon head) 82dB(A)
(Blade) 81dB(A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN62841
Vibration emission value
ah,
w
= (Nylon head) 7.8m/s2
(Blade) 4.5m/s2
Uncertainty K = 1.5m/s2
The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of
exposure.
WARNING
○ The vibration and noise emission during actual use of
the power tool can differ from the declared total value
depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
○ Identify safety measures to protect the operator that are
based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18
CG18DA(L)_C99750571_311_EU
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CG18DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CG18DA in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info