816209
23
Zoom out
Zoom in
Previous page
1/380
Next page
English
23
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult
your dealer or the HiKOKI Authorized Service Center.
Symptom Possible cause Remedy
The tool does not function. The battery is dead. Recharge the battery.
The battery is not fully inserted. Pull out the battery and remove any
debris from the battery compartment.
Use cotton swabs or similar materials
to remove dirt or water from the
battery terminals.
Insert the battery firmly until it clicks
into place.
The battery is overheated. Stop using the tool. Remove the
battery and allow the battery to cool
in a shaded, well-ventilated area.
The power is not on. Press the power switch on the
housing.
The tool features an auto power off
function that turns the power off
automatically after one minute if the
operator does not operate the lever.
The operator attempted to pull the
lever without pressing the lock lever. The tool will not allow operation of the
lever unless the operator presses the
lock lever to release the safety lock
mechanism.
Grasp the handle and press the lock
lever while pulling the lever.
Excessive vegetation entangled in
the guard and nylon head overloaded
the motor.
If overloaded, the motor may cut out
to protect the tool and battery.
Turn off the power, remove the
battery, and clear the cause of the
overload.
The tool can be used again after
turning the power back on.
The tool starts, then stops soon. The battery is low. Recharge the battery.
The battery is overheated. Stop using the tool. Remove the
battery and allow the battery to cool
in a shaded, well-ventilated area.
The tool is overloaded. Reduce the cutting depth to reduce
the load.
The speed cannot be changed. The battery is low. Recharge the battery.
Vibration is excessive. The cutting attachment is not
correctly attached. Reattach the cutting attachment.
The cutting attachment is cracked,
broken, or deformed. Replace the cutting attachment.
The handle is not securely attached
to the main pipe. Attach securely.
The guard is not securely attached to
the main pipe. Attach securely.
The blade does not cut well The tip of the blade is damaged Replace the blade.
2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18
CG18DA(L)_C99750571_311_EU
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CG18DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CG18DA in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info