467111

Graupner MC 32 HOTT Manual

95
Zoom out
Zoom in
Previous page
1/345
Next page
95
Program description - Base setup models | Helicopter models
Press and hold the SET button on the receiver
while the LED continues to blink red for about
3 seconds then, after about another 3 seconds,
begins to blink red/green. The SET button on the
receiver can now be released. As long as this LED
blinks red/green, the receiver is in bind mode.
Now, within this 3 second period, start the so-
called “receiver binding” process for the receiver
to the currently active model memory with a brief
tap on the centre SET key of the right touch pad.
At this time, the screen’s display will blend in a
message window for the duration of the “binding”
process.
Model name
Stick mode 1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module bind
HoTT
Graubele
1234g/111111
SEL BD1 BD2 BD3 BD4
FINDING...
If the receiver’s LED, again blinking red, changes
within about 10 seconds to continuous illumination
in green, the binding process has been success-
fully completed. Your model-memory to receiver
combination is now operationally ready. At this
time the screen will now display “ bind “ (bound)
instead of “n/a” (not attached).
Model name
Stick mode 1
bind
BASIC SETTING,MODEL
Info
n/a
n/a
Module bind
HoTT
Graubele
1234g/111111
SEL BD1 BD2 BD3 BD4
On the other hand, should the LED on the receiver
blink red for longer than about 10 seconds, the
binding process has failed. In this case the screen
will continue to show the status as “n/a”. If this
should happen, try changing the position of anten-
nas then repeat the entire procedure.
• Receiver GR-12L
At the receiver, the red LED lights. Press and hold
the SET button on the receiver until the red LED
goes out after about 3 seconds for a further 3 sec-
onds. You can now release the SET button on the
receiver. As long as the LED is off, the receiver is
in bind mode. Start now-as described above-within
these 3 s to bind the receiver to the current model
memory. If the LED of the receiver is still dark and
the display in the transmitter changes to “b”, the
binding process has been completed success-
fully. However, the red LED will light up red again
at the receiver, the binding process has failed.
At the same time appear in the line “module” of
the display again “n / a”. If necessary, change the
positions of the antennas involved and repeat the
entire procedure.
Binding other receivers
The binding channel you have chosen is already
bound (as indicated by the “bind” status). This binding
is to be replaced by another. After initiating the RF
bind process, instead of displaying “BINDING”, the
message shown below appears.
Model name
Stick mode 1
geb.
BASIC SETTING,MODEL
Info
n/a
n/a
Module geb.
HoTT
Graubele
1234g/111111
SEL BD1 BD2 BD3 BD4
RF
off
OK
is turned
Drop down two lines in the screen and switch off the
RF module as described on the page in section “RF
module”. Afterward, return again to the “Module” line
and restart the binding process as described above.
Alternatively, the transmitter can be switched off
briefl y then, after switching it back on again, respond
to the message window that appears …
OFFON
Please select
RF on/off?
… with “OFF” …
ON
Please select
RF on/off?
OFF
… then confi rm the selection with a brief tap on the
centre SET key of the right touch pad. From the base
screen jump again into the “Module” line of the »Ba-
sic settings, model« menu and restart the binding
process.
Dissolving a bond
Proceed as described above to initiate the binding
process but WITHOUT fi rst putting a receiver in bind-
ing readiness.
… 95 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info