Manual Graupner MC 32 HOTT (page 94 of 345) (English)

467111

Zoom out

Zoom in

1/345

94 Program description - Base setup models | Helicopter models

Module

Model name

Stick mode 1

n/a

BASIC SETTING,MODEL

Info

n/a

Module bind

HoTT

Graubele

1234g/111111

SEL BD1 BD2 BD3 BD4

The mc-32 transmitter has a HoTT RF module as

standard equipment. In addition to the built-in mod-

ule, there is a connector for an external RF module

behind one of the two front cover ﬂaps (see page 25)

and a switchover to an external module connected

there can be affected per software. To do this, use the

selection keys of the left or right touch pad to move

the marker frame left to the “Module” selection ﬁeld

above the “SEL” column label.

HoTT

To be able to connect to the transmitter, Graupner

HoTT receiver must be connected to at least one

model memory “of their” Graupner HoTT transmitter.

This process is commonly referred to by the English

term “binding” and can be repeated anytime. This

“binding” of a receiver is by default always memory-

specic, but may at any time and for any unbound

model memory of a transmitter in the menu that

appears row “binding type”, see above, to transmitter

specic, and can be reversed, changed.

Important notices:

• During the binding procedure be

sure the transmitter’s antenna is

always far enough away from the

receiver’s antenna.

To be on the safe side, keep them at

least one meter apart. Otherwise there

is a risk of a faulty connection to the

return channel and malfunctions will

result.

• Pay close attention to the correct power

supply of the receiving system. Too low

supply voltage while responding the

LEDs of the receiver as described below

on your Binding effort, yet there is no

proper HoTT Synchronization.

• When binding additional receivers, note

that any other – switched on – receivers

already bound to the transmitter will

fall into Fail safe mode during the

transmitter-side “binding” period.

“Binding” multiple receivers per model

Multiple receivers per model can be bound if desired,

whereby mc-32 HoTT programs offer the potential

for managing up to two receivers directly and for di-

viding up the transmitter’s 16 control channels (max)

in any arrangement among these receivers under

menu control. Refer to additional details further down

in this section. First bind the receivers individually as

described below.

When the system is actually in use, the

only receiver which creates a telemetry

link to the transmitter is either the last

receiver to be bound, or the receiver which you

selected in the “TEL.RCV.” line of the »Telem-

etry« menu, for example:

TELEMETRY

SETTING & DATAVIEW

SENSOR SELECT

RF STATUS VIEW

VOICE TRIGGER

TELEMETRY RCV BIND. 1

Any telemetry sensors which may be built into the

model should therefore be connected to this receiver

because the transmitter only receives and evaluates

data from the return channel of the receiver activated on

this line. The second, and all other receivers, operate in

parallel but are fully independent in slave mode.

“Binding” transmitter and receiver

Use the  selection keys of the left or right touch

pad to move into the “Module” line. The marker frame

will be positioned by default to the column for the next

free binding channel. In the example shown in the

figure below, the marker frame is positioned above the

column label “BD2” because the binding channel in the

column labeled “BD1” is already in use by default for

the receiver which was delivered with the set.

Model name

Stick mode 1

n/a

BASIC SETTING,MODEL

Info

n/a

Module bind

HoTT

Graubele

1234g/111111

SEL BD1 BD2 BD3 BD4

If not already off, now switch the receiver on.

• Receiver GR-32 DUAL

The red LED on the GR-32 HoTT receiver will

blink.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MC 32 HOTT Manual

Product: