Manual Garmin GPSMAP 2110 (page 12 of 106) (English)

583758

12

Zoom out

Zoom in

Previous page

1/106

Next page

4 GPSMAP 2106/2110 Owner’s Manual

GETTING STARTED > TURNING ON THE GPSMAP 2106/2110

Turning on the GPSMAP 2106/2110

Before you turn on the GPSMAP 2106/2110, make sure the unit and GPS 17

antenna are correctly installed on your vessel according to the instructions in the

GPSMAP 2106/2110 & GPS 17 Installation Instructions.

The ﬁrst time you turn on the GPSMAP 2106/2110, the GPS 17 receiver

must collect satellite data and determine its current location. To ensure proper

initialization, the GPSMAP 2106/2110 is shipped from the factory in AutoLocate

mode.

To turn on the GPSMAP 2106/2110:

1. Press and hold the POWER key until the unit turns on.

2. When I Agree is highlighted on the Warning Page, press ENTER to open

the Map Page.

NOTE: The ﬁrst time you turn on the unit, you are asked if you want to start

the retail demonstration. Select No, and press ENTER.

To turn off the GPSMAP 2106/2110:

Press and hold the POWER key until the unit turns off.

Adjusting the Backlight

You can adjust the screen backlighting on the GPSMAP 2106/2110 from any page

by using the POWER/BACKLIGHT key.

To adjust the backlight level:

1. Press and release the POWER/BACKLIGHT key.

2. Press up on the ROCKER to increase the brightness, or press down to

decrease.

TIP: After you open the Backlight adjustment window, press the

POWER/BACKLIGHT key repeatedly to cycle through the three

backlight settings: Highest, Middle, and Lowest.

Highest Middle Lowest

3. Press ENTER or QUIT to close the Backlight adjustment window.

1

I have acquired a Garmin 2110 with a GPS17.
The cable between the two has been carefully cut - I assume to remove it from the previous vessel. I have connected all the cables together as per the Basic Installation shown in the handbook. All works fine.
My question is how can i reconnect the two (front and rear) looms together. The wires from the GPS17 are too fine to solder and not of sufficient size as to allow connection by electrical Mobloc.
Can anyone help me by telling me what they have used to connect these looms together?
Thanks in anticipation
Ian Hutchinson Submitted on 15-4-2021 at 11:46
Reply Report abuse
I have just acquired a Garmin 2110 and GPS17.
The wires that connect the two together have been carefully cut - I assume to enable the units to be removed from the previous vessel. I have connected all the wiring together as per the Basic Wiring diagram and all worked perfectly.
However the wires from the GPS17 are extreamly delicate and will not (maybe my inexperience ) allow solder connections in order to make the installation complete. My question is what can I use to make a permanent fixing of the two (front and rear) looms?
I have tried using a small mobloc but the wires in the GPS17 loom are too fine to make a good connection.
Any help would be greatly appreciated
Ian Hutchinson Submitted on 15-4-2021 at 11:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Garmin GPSMAP 2110 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 2110 in the language / languages: English as an attachment in your email.

The manual is 6,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info