724647
14
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
24 25
1. Lay the unit down so that the fuel tank bracket
(39) is on the ground or on a secure surface.
Lift the gearbox end of the lower shaft (15) to
gain access to the output spindle (20).
2. Line up the tabs on the clip-on line trimmer
guard attachment (33) with the large slots on the
brushcutter guard (17). There are 2 main release
clips; one on each end of the clip-on line
trimmer guard attachment (33). This needs to
line up with the large slots on the brushcutter
guard (17) (Fig AJ).
3. When all tabs are lined up in position, push the
tabs on the clip-on line trimmer guard
attachment (33) into the slots, and the release
clips into the large slots. You will hear clicks
when the release clips are secure. (Fig. AK)
NOTE: Before using the line trimmer, remove the
cut o blade protector. After using the line
trimmer, it is recommended to replace the
blade protector.
4. To fully secure the clip-on line trimmer guard
attachment (33) to the brushcutter guard (17),
insert and secure the screw using the supplied
spark plug spanner / blade nut wrench /
screwdriver combination (36), using the
screwdriver end of the tool. Secure until tight (Fig AL).
Fitting the Spool and Line Assembly on the Line Trimmer
NOTE: If the unit has been used as a brushcutter rst, the brushcutter blade
will need to be removed before tting the spool and line assembly.
Refer to “Changing/Removing the Brushcutter Blade for instructions on how
to remove the blade on page 22.
NOTE: Always ensure the engine is turned o before undertaking this assembly.
1. Lay the unit down so that the fuel tank bracket (39) is on the ground or on
a secure surface. Lift the gearbox end of the lower shaft (15) to gain access
to the spindle (20).
AJ.
AK.
AL.
IMPORTANT: Ensure the inner ange is mounted on the spindle of the line
trimmer. The outer ange (29), the protector (27), the 3T brushcutter blade
(28) and the blade nut (26) are NOT required when the line trimmer spool
& line assembly (35) is being tted.
Keep these components in a safe place. The 3T
brushcutter blade (28) should be placed back in
the cardboard packaging/envelope.
2. Place the spool and line assembly (35) on the
spindle (20) and thread on to the spindle nger
tight in an anti clockwise direction all the way
down until the back of the spool makes contact
with the inner ange (30) (Fig AM),
3. Insert the long end of the supplied 4mm allen
key (37) through the spindle lock entry hole (19)
and into the hole on the inner ange (30).
(This locks the spindle allowing the spool and
line assembly (35) to be secured). Further tighten
the spool and line assembly (35) ensuring the
assembly is tight on the spindle (20) and inner
ange (30) before removing the 4mm allen key
from the spindle hole to release the spindle
being locked (Fig. AN).
Removing the Spool and Line Assembly
NOTE: Always ensure the engine is turned o before undertaking this assembly.
1. Lay the unit down so that the fuel tank bracket (39) is on the ground or
on a secure surface. Lift the gearbox end of the lower shaft (15) to gain
access to the output spindle (20).
2. Insert the long end of the supplied 4mm allen key (37) through the
spindle lock entry hole (19) and into the hole on the inner ange (30).
(This locks the spindle allowing the spool and line assembly to be
removed). (Fig. AN)
3. Loosen the spool and line assembly (35) in a clockwise direction until it
can be removed from the spindle (20). Remove the allen key (37) locking
the spindle (20) once the spool and line assembly (35) has been removed.
AN.
AM.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info