724647
15
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
26 27
NOTE: If replacing the spool and line assembly (35) with the supplied
additional spool and line assembly, follow the “Fitting the Spool and Line As-
sembly on the Line Trimmer instructions on the previous page.
If replacing just the spool line on the supplied spool and line assembly,
refer to the instructions following this section.
Changing the line only on the Spool and Line Assembly
NOTE: Always ensure the engine is turned o before undertaking this
assembly.
NOTE: The spool provided on this product is a rapid or easy wind type spool.
There is no disassembly of the spool components. The following steps will
guide you through the process.
NOTE: The spool & line assembly (35) does not need to be removed from the
lower shaft (15) of the line trimmer, however, if it is easier, it can be removed
from the lower shaft (15), especially for the rst time you re-load / re-wind
the line & become familiar with the process.
The line to suit this type of spool assembly is 2.4mm diameter line, with a
length not exceeding 2.6m.
1. Remove any existing line protruding from either eyelets in the spool
assembly (35). If there is no line left inside the spool, the line can easily
be pulled outwards from the eyelets. If the line will not pull out and is
jammed, the spool will need to be opened and the jammed line released.
Refer to the section on “Clearing a Jammed Spool” following this section.
2. When looking at the top cover of the spool, there is an arrow on the
bump knob (34) pointing outward, and an arrow on the spool cover
pointing inwards, with the word “LINE” above the
arrow. Whilst holding the spool housing, rotate
the bump knob (34) in a clockwise direction (as
shown by the rotating arrow on the bump knob)
until the two outer arrows line up together (Fig
AO). Depressing the bump knob (34) slightly
while rotating can assist in rotating the bump
knob (34).
AO.
3. Cut a length of 2.4mm diameter nylon line to a length of 2.6m, ensuring
the line is cut cleanly. If the rst 150mm of line is curved, try and
straighten the line as much as possible for entry into the spool.
4. Following the arrow direction on the spool cover, pass one end of the
nylon line through the eyelet until it passes through the spool and out
through the opposite side (Fig AP). The line should pass through the
spool with the rst 150mm of line. If it does not pass through the other
side within this line length, check the arrows align on the spool cover
and the bump knob (34). Also check if there is
a curve in the line. A straight section of line is
always better than a curved section. Remove
the line from the eyelet and retry and change
the angle of entry. Slight pressure on the bump
knob (34) my also assist, depending on the
curve on the line.
5. Pull the line through the spool so both lengths
of line extending from each eyelet are the same
length (Fig AQ).
6. Rotate the bump knob in a clockwise direction;
also the direction of the rotation arrow on the
bump knob (34). As the bump knob (34) is
rotated, the line will be evenly be drawn into
the spool and evenly wind the line in place.
Continue to wind the line into the spool until
approx. 100mm of line extends out from the
eyelets (Fig AR).
NOTE: Slight downward pressure on the spool
will assist in the rotating action.
7. The spool and line is now ready for use. If the
spool & line assembly (35) was removed from
the lower shaft (15) for this process, ensure it is
correctly tted as per the instructions on
page 24.
AQ.
AR.
A P.
CLOCKWISE
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info