724647
13
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
22 23
in an anti clockwise direction to fully tighten the blade nut (26) and secure the
3T brushcutter blade (28) into position. Ensure the 3T brushcutter blade (28) is
secured tight before removing the allen key (37) from the spindle hole (Fig AI).
Changing/Removing the Brushcutter Blade
NOTE: Always ensure the engine is turned o
before undertaking this task.
1. Lay the unit down so that the fuel tank bracket
(39) is on the ground or on a secure surface. Lift
the gearbox end of the lower shaft (15) to gain
access to the output spindle (20).
2. Insert the long end of the supplied 4mm allen
key (37) through the spindle lock entry hole (19)
and into the hole on the inner ange (30).
(This locks the spindle allowing the blade bolt to
be secured) (Fig. AH).
3. Using the supplied spark plug spanner / blade
nut wrench / screwdriver combination (36),
loosen the blade nut (26) by turning in a
clockwise direction (Fig. AI).
4. Remove the blade nut (26), protector (27), outer
ange (29), and 3T brushcutter blade (28) in this
order.
NOTE: If you are removing your brushcutter
blade to use the unit as a line trimmer, refer to page 24/25 for instructions
on “Fitting the Spool and Line Assembly on the Line Trimmer.
5. Replace with the new blade and follow steps 3-8 in the “Fitting the
Brushcutter blade section.
O
To commence with operation of the brushcutter, refer to the instructions
on page 33 .
NOTE: Ensure you have lled the unit with the correct fuel and oil before
proceeding to start the unit.
NOTE: This is a 4 stroke brushcutter / line trimmer.
The motor MUST be lled with 70mL of SAE 10W/30 BEFORE starting.
Fresh unleaded fuel must be used in this unit.
Do NOT use ethanol based fuels. Do NOT mix oil with fuel.
AH.
AI.
Tips for Operation
Always use the double shoulder strap harness (31) when using the
brushcutter to avoid serious personal injury.
Hold the brushcutter with one hand on the trigger handle and the other
hand on the J handle (12). Keep a rm grip with both hands while in
operation. The brushcutter should be held at a comfortable position with
the double shoulder strap attachment point (38) about hip height.
Maintain your grip and balance on both feet. Position yourself so that you
will not be drawn o balance by the kick-back reaction of the 3T brushcutter
blade (28).
Exercise extreme caution when using the 3T brushcutter blade (28) with
this unit. Blade thrust is the reaction which may occur when the spinning
3T brushcutter blade (28) contacts anything it cannot cut. This contact may
cause the 3T brushcutter blade (28) to stop for an instant, and suddenly
“thrust the unit away from the object that was hit.
This reaction can be violent enough to cause the operator to lose control of
the unit. Blade thrust may occur without warning if the blade snags, stalls or
binds. This is more then likely to occur in areas where it is dicult to see the
material being cut.
For cutting ease and safety, approach the weeds being cut from the right to
the left. In the event that an unexpected object or woody stock is
encountered, this could cause the blade thrust reaction.
Specic Assembly for use as a Line Trimmer
Fitting the Clip-on Guard Attachment to the Line trimmer
NOTE: Always ensure the engine is turned o before undertaking this task.
Always use the double shoulder strap harness (31) when using the line
trimmer to avoid serious personal injury.
NOTE: the clip-on line trimmer guard attachment (33) must be secured to
the brushcutter guard (17) before ANY line trimming work is undertaken.
NOTE: Always ensure the engine is turned o before undertaking
this assembly.
WARNING: There is a cut o knife (32) on the clip-on line trimmer
guard attachment (33). Use gloves to t the clip-on line trimmer
guard attachment (33) to avoid injury.
Operation of the Brushcutter
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info