724647
12
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
20 21
2. Connect the clip at the front to secure the double
strap shoulder harness (31) into position on your
body. (Fig. Y) NOTE: The side pad guard will be
located on your right hand side.
3. To adjust the double shoulder strap harness (31)
on your body, tighten or loosen the front straps
adjusters. (Fig. Z)
4. Ensure the metal connector clip is attached onto
the side pad guard correctly. When in the correct
position, the long metal tab (as shown in
Fig. AA with the arrow on it) needs to be holding
the metal connector clip in place.
5. To attach to the unit, insert the clip on the side
pad guard through the double strap shoulder
harness attachment point (37) (Fig. AB)
The location of the side pad guard can also be
changed by tightening or loosening the adjuster
on the side pad guard.
The double shoulder strap harness (31) is tted
with a quick release clip which allows rapid
removal of the appliance from the harness.
To activate the quick release clip so as to remove
the appliance, “Pull the red tab thus withdraw
-
ing the metal tab. The attaching clip will then
release from the harness.
Fitting the Brushcutter Blade
NOTE: Always ensure the engine is turned o
before undertaking this task.
NOTE: Before tting, check the diameter of the
cutter is 255mm, and the Bore size is 25.4mm.
Do NOT
proceed if the cutter is dierent to these
specications.
Y.
AB.
AA.
Z.
1. Lay the unit down so that the fuel tank bracket (39)
is on the ground or on a secure surface. Lift the
gearbox end of the lower shaft (15) to gain access
to the spindle (20).
2. Place the inner ange (30) over the spindle (20)
ensuring the spline on the spindle (20) aligns with
the spline in the inner ange (30). Fully seat the inner
ange (Fig AC).
3. Place the 3T brushcutter blade (28) over the spindle
(20) and locate on the raised centre of the inner
ange (30). (Fig AD) . Ensure the direction of rotation
of the blade as indicated by an arrow on the blade
corresponds with the arrow direction on the top of
the guard.
4. Place the outer ange (29) over the spindle (20) on
top of the 3T brushcutter blade (28) (Fig. AE),
followed by the protector (27).
5. Place the blade nut (26) on to the spindle (20) and thread the nut in an anti
clockwise direction all the way down to the protector (27) (Fig. AG).
6. To fully tighten the 3T brushcutter blade (28) onto the spindle (20) ensure the
3T brushcutter blade (28) is still correctly located on the inner ange (30).
7. Insert the long end of the supplied 4mm allen key (37) through the spindle lock
hole (19) and into the hole on the inner ange (30). (This locks the spindle
allowing the blade bolt to be secured) (Fig. AH).
8. Whilst holding the supplied allen key (37) in position to lock the spindle, use the
supplied spark plug spanner / blade nut wrench / screwdriver combination (36)
AC.
AD.
AE. AF. AG.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info