724647
16
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
28 29
Clearing a Jammed Spool
NOTE: Always ensure the engine is turned o
before undertaking this assembly.
The spool & line assembly (35) does not need to
be removed from the lower shaft (15) of the line
trimmer, however, if it is easier, it can be removed
from the lower shaft (15) for this process.
In the case where the spool will not feed out
line when the bump knob (34) is bumped on
the ground at high speed, or the line will not
pull through when the line needs replacing, the
following process should be followed to open the
spool & line assembly (35) to check the lay of the
line on the inner spool.
1. To open the spool & line assembly (35), press
rmly in the centre of the two securing tabs on
each side of the spool assembly (35), one at a
time (Fig AS). When pressed rmly, the spool
cover can be lifted when released. Remove the
top spool cover.
2. Remove the internal spool itself with the
jammed line, fully from the spool housing
(Fig AT).
3. Remove all the existing line from the spool
completely (Fig AU).
AU.
AS.
AT.
4. Reassemble the spool assembly by rstly
centralising the compression spring in the base
of the spool housing, then replacing the spool
on top of the spring followed by replacing the
spool cover on the spool (Fig AV).
NOTE: When replacing the spool cover, ensure
the clips of the spool housing align with the
spool cover. When the spool cover is located
on the spool housing, push down rmly on the
cover to ensure the clips have engaged on the
cover and the cover cannot pull o.
5. Check the removed line for damages, or use new
line. Reload new line onto the spool as per the
previous section “Changing the line only on the
Spool and Line Assembly.
Prior to operating the line trimmer after line has
been added, it is suggested to trim the lines so
they are even and just short of the cutting blade
on the guard. This prevents a possible large
section of line being trimmed at high speed.
When you start the line trimmer, bump the head
of the spool on the ground to enable the cut o
knife on the guard to cut the line to the
required length for use.
AV.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info