Manual Futaba FP8SSAP (page 34 of 44) (English)

30094

Zoom out

Zoom in

1/44

ADJUSTMENTS AND FLIGHT TECHNIQUES

•SNAP ROLL SWITCH (TIMER IS OPTIONAL)

•When this function is used, snap rolls can be

performed by pushing the Snap Switch 13 . Snap

roll directions can be set using Control Switches

and

1 Set Safety Switch [29] on the trimmer panel

ACT. Monitor Lamp (D) will blink.

2 A snap roll in the direction set by switches 34

and 35 can now be performed by pushing Con-

trol Switch 13 to ON. The aircraft will con-

tinue to roll as long as the switch is held ON

unless the optional timer function is installed.

3 The

optional

timer function

can

used

automatically stop the snap roll. Trimmers

[25], [26], [27]. and [28] can be used to set the

time in each direction. The time can be varied

from 0.2 to 2 seconds.

NOTE: The Snap Switch 13 is positioned so

that it is easy to reach. When the snap

roll function is activated, you must

use great care not to push the switch

inadvertently. When the snap roll

function is not desired, always set

Safety Switch [29] to INHIB.

SNAP ROLL TIMER (OPTION)

These are the snap roll time setting

trimmers and snap roll function

safety switches.

25 Right up snap roll time set-

ting trimmer for button 34 .

The snap roll time is settable

from 0.2 to 2 seconds.

26 Right down snap roll time

setting trimmer for button

35 . The snap roll time is set-

table from 0.2 to 2 seconds.

[27] Left up snap roll time setting

trimmer for button 36 . The

snap roll time is settable from

0.2 to 2 seconds.

28 Left down snap roll time set-

ting trimmer for button 37 .

The snap roll time is settable

from 0.2 to 2 seconds.

Snap roll function safety

switch.

•PROGRAMMABLE MIXING AND EXAMPLES

Fig. 57

• Programmable mixing of any two channels

desired is possible using the mixing board on the

trimmer panel. Programmable mixing is NOT a

memory function and all programmed mixing

is of the unidirectional type.

•The

Master

and

Slave

channels

can

desig-

nated using Jumper Connectors 13 and 14 . The

mixing amount in each direction of servo move-

ment is adjustable using Trimmers 11 and 12 .

•When Programmed Mixing is not in use. Con-

nectors 13 and 14 should be placed in the

INHIB position as shown in Fig. 57.

•When Function Select Switch 30 is set to P.

MIX, programmed mixing can be switched ON

and OFF in fhght using Control Switch (16).

When Switch 30 is set to RUDD D/R, program-

med mixing will remain ON if activated using

Connectors 13 and 14, and Control Switch 16)

can be used to turn the Rudder Dual Rate func-

tion ON and OFF.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSAP in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba FP8SSAP Manual

Product: