522136
28
Zoom out
Zoom in
Previous page
1/47
Next page
21
TEST: Conducts diagnostic tests. For
further details, see paragraph 3.7.
LCD PATTERN: Tests the LCD. For further
details, see paragraph 3.8
MEMORY CLEAR: The memory can be
cleared to start afresh with default menu
settings.
1. At the installation menu, press to
choose MEMORY CLEAR.
2. Press to open the options window.
: YES
: NO
Clear memory display
4. Press to clear the memory. Beeps
are generated while the memory is
being cleared.
5. To restore normal operation, turn off the
power and then turn it on again.
NMEA PORT: Sets the function of the
NMEA port. For further details, see
paragraph 4.7.
NMEA MIX: Turns data mixing on or off.
For further details, see paragraph 4.7.
GPS WAAS: Chooses how to use the
WAAS signal.
Note: WAAS is currently in the
developmental phase. During the
developmental phase the reliability and
availability of the WAAS signal cannot be
guaranteed. Therefore, any position data
should be verified against other sources to
confirm reliability.
1. Display the Installation menu.
2. Choose GPS WAAS and then press
to open the GPS WAAS options
window.
Off
WAAS options window
3. Press or to choose “WAAS-02”
(test signal). When the system becomes
operational (in 2003), set to “00”
(regular WAAS signal).
4. Turn off the power.
BOTTOM LEVEL: If the depth indication is
unstable in automatic operation, or the
bottom echo cannot be displayed in the
darkest gray tone by adjusting the gain
controls in manual operation, you may
adjust the bottom echo level detection
circuit, for both 50 kHz and 200 kHz, to
stabilize the indication. Generally, lower the
bottom level for inner hull installation where
the receive level is too low. If the bottom
level is too low it may be difficult to
discriminate fish from the bottom, resulting
in unstable depth indication. And if the
bottom level is too high the depth indication
may not appear.
1. At the installation menu, press to
choose SET BOTTOM LEVEL and then
press . Several seconds later the
following display appears.
Bottom level
+0 (200k: -100 - +100 )
+0 ( 50k: -100 - +100 )
Bottom level display
2. While observing the picture, use or
to set 200 kHz; or to set 50 kHz.
Set up for optimum picture.
3. To restore normal operation, turn off the
power and then it on again.
Note: The mode must be other than NAV
DATA to show the bottom level display.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno LS-6100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno LS-6100 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info