522136
30
Zoom out
Zoom in
Previous page
1/47
Next page
23
3.6 Troubleshooting
The table below provides basic
troubleshooting procedures which the user
may follow to restore normal operation.
Troubleshooting table
If… Then check
neither echo nor
fixed range scale
appears
battery voltage.
fuse.
power supply.
power cable.
no echo appears
but the fixed
range scale
appears
if display advance
speed is set to “Stop.”
transducer plug
echo appears but
no zero line
if range shifting is set
to “0.”
sensitivity is low
gain setting.
if air bubbles or marine
life is clinging to the
transducer face.
if sediments are
present in the water.
if the bottom is too soft
to return an echo.
there is extreme
interference or
noise
if the transducer is too
close to the engine.
if the unit is properly
grounded.
if other echo sounders
of the same frequency
as own are being
operated nearby.
the speed/water
temperature
readout is
unrealistic or not
present
sensor plug.
the position
readout is
unrealistic or not
present
the connection
between sounder and
navigator.
navigator.
3.7 Diagnostics
If you feel your unit is not working properly,
conduct the diagnostic test to find the
problem. If you cannot restore normal
operation, contact your dealer for advice.
1. Turn on the power while pressing the
[MENU/ESC] key. Continue pressing
the [MENU/ESC] key until the
Installation menu appears.
SIMULATION On
TEST ...
LCD PATTERN ...
MEMORY CLEAR
NMEA PORT : In/Out
NMEA MIX : Off
GPS WAAS* : Off
SET BOTTOM LEVEL ..
Installation Menu
* = Setting cannot be changed when
NMEA PORT setting is "In/In."
Installation menu
2. Press to choose TEST.
3. Press to start the test.
ROM : OK
RAM : OK
NMEA :
Temp : 68.2
°
F
Speed : 10.0km/h
Power : 12.4 V
Body : 39
°
C
Program No. 0252308-01.**
Push [MENU] 3 times to exit.
Level bar
** = Program version no.
Water
Temperature,
Speed
Battery Voltage
Temperature
inside display
unit
(Unit fixed at
°
C.)
Test display
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno LS-6100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno LS-6100 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info