535711

Friedland HISK1 GlobalGuard Alarm System Manual

19
Zoom out
Zoom in
Previous page
1/78
Next page
19
The internet connection must be free from
any firewalls/restrictions that might prevent
remote access.
INSTALLING THE IP GATEWAY
1. Connect the IP Gateway to a spare LAN port
on your home broadband router as shown
below:
Connecting gateway to router
2. Connect the 5V DC adaptor and turn on.
3. Check that the power LED on the gateway
turns green which could take up to 1 minute.
LED indications
LINKING AN IP GATEWAY TO THE
CONTROL PANEL (OPTIONAL)
The gateway supplied in this kit has been
supplied pre-linked to the Control Panel at
the factory therefore you do not need to
repeat this. However in the future, should it
ever need to be linked again to the Control
Panel, this can be done as follows:
With the Control Panel in standby mode, enter
programming mode by pressing the following
keys:
,
Use the and buttons to scroll
through the menu until ‘5. Comms’ is displayed.
and press . ‘5-1 Comms Device’ will be
displayed.
Press the enter button again and ‘Input
(01-12) Device NO.’ will be displayed
Using the keypad, enter a device number
between 1 and 12 on the keypad to which you
wish to add the gateway to. If a device is
already linked to this channel then select an
alternative device channel.
Press the enter button and using the
and buttons scroll until ‘:2
Learning ID’ is displayed.
Press the enter button again and
“Waiting Learning..” will be displayed.
Within 30 seconds of entering device learning
mode, press and hold the “Link” button located
on the rear side of the gateway until “Learning
OK” is displayed
User access PIN code
The 4 camera connection LEDs
indicate the status of up to 8
cameras:
1. When connecting 1-4 cameras,
LEDs 1-4 will turn green
2. When the 5
th
camera is added,
LED 1 will turn amber (and so on).
3. If camera 1 is disconnected but
camera 5 is still active, LED 1 will
turn red (and so
on).
RF Connection to Control
Panel LED Green
OK/orange failed
Power /
Connection to
internet LED – Green
- ok/Red -failed
IP Gateway
Router
LAN port
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland HISK1 GlobalGuard Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland HISK1 GlobalGuard Alarm System in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info