535711

Friedland HISK1 GlobalGuard Alarm System Manual

20
Zoom out
Zoom in
Previous page
1/78
Next page
20
DELETING THE IP GATEWAY FROM THE
CONTROL PANEL (OPTIONAL)
With the Control Panel in standby mode, enter
programming mode by pressing the following
keys:
Use the and buttons to scroll
through the menu until ‘5. Comms’ is displayed
and press . ‘5-1 Comms Device’ will be
displayed.
Press the enter button again and ‘Input
(01-12) Device NO.’ will be displayed.
Using the keypad, enter a device number
between 1 and 12 on the keypad to which you
wish to remove the gateway from.
Press the enter button and using the
and buttons scroll until
‘:4 Device Remove”’ is displayed.
Press the enter button again and
“Waiting Learning..” will be displayed.
“Select Yes->
* No->#” will be displayed.
Enter
* on the control panel to remove the
gateway.
PASSIVE INFRA-RED (PIR)
MOVEMENT DETECTOR
PIR Movement Detectors detect movement in a
protected area by detecting changes in infra-red
radiation levels caused for example when a
person moves within or across the PIR’s
detection pattern. If movement is detected an
alarm will be triggered, (if the system is armed).
PIR Detectors will also detect animals, so
ensure that pets are not permitted access to
areas fitted with PIR Movement Detectors when
the system is armed.
The Detector incorporates an anti-tamper
protection feature to protect against attempts to
interfere with the device. If the battery cover is
removed, an alarm will immediately occur at any
time, (unless the system is in Program or Test
Modes).
The PIR Detector also incorporates a sensitivity
adjustment feature (Hi or Low setting) to
compensate for situations where the detector
may be triggered by environmental changes,
(e.g. insects, air temperature, etc).
To conserve power and maximize battery life the
PIR Detector will only detect movement if there
has been no movement detected within the
previous 2 minutes, (this is known as the
detectors sleep period).
The PIR Detector is powered by a PP3 Alkaline
battery which under normal conditions will have
an expected life of approximately 1 year. When
the battery level drops, with the PIR in normal
operation mode and the battery cover fitted, the
LED behind the detection window will flash.
When this occurs the battery should be replaced
as soon as possible. (Note: in normal
operation, the LED behind the lens will not flash
on detection of movement).
The system allows you to link one Detector to a
zone, provided that the Detector is mounted
within effective radio range of the Control Panel.
Link push button
User access PIN code
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland HISK1 GlobalGuard Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland HISK1 GlobalGuard Alarm System in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info