778502

Festool TKS 80 EBS Manual

39
Zoom out
Zoom in
Previous page
1/276
Next page
► Adjust the stop rail [6-7] in such a way that
the triangular arrow lies within the green
sticker [6-8].
► Tighten the screw [6-6].
The rip fence (Fig. 6a) is ready to use.
Preset profile setting rail as high or low stop
per
The preset profile setting rail can be used
as a high or low stopper. To do this, the
stop rail is inserted either upright or flat.
The low stopper is used to prevent a colli
sion with the guard, e.g. in the case of mi
tre cuts with a saw blade swivelled to 45°.
► Undo the screw [6-6].
► Pull out the stop rail [6-7], flip it and insert
it again.
► Adjust the stop rail [6-7] in such a way that
the triangular arrow lies within the green
sticker [6-8].
► Tighten the screw [6-6].
Setting the cutting width
► Loosen the screw [6-15].
► Set the required cutting width.
► Tighten the screw [6-15].
Cutting width ≤ 3 mm
NOTICE
SawStop AIM technology is triggered or
the TKS 80 EBS does not start.
Distance between saw blade and fence too
small.
► When sawing cutting widths of ≤ 3 mm, use
a support ≥ 19 mm.
Preset profile setting rail as a sliding mecha
nism
► Release the rotary knob [6-1].
The preset profile setting rail [6-10] can be
moved along the V-profile [6-12] as a sliding
mechanism.
Preset profile setting rail as a cross and angle
stop
► Release the rotary knob [6-1].
► Undo the screw [6-4].
► Lift the fixing pin [6-3] and set the stop
rail [6-7] to the required angle using the
scale [6-5].
► Click the fixing pin [6-3] into place.
► Tighten the screw [6-4].
► Undo the screw [6-15].
► Move the stop rail [6-7] out of the cutting
area.
► Tighten the screw [6-15].
The preset profile setting rail [6-10] can be
moved along the V-profile [6-12] as a sliding
mechanism.
The cross and angle stop (Fig. 6b) is ready for
use.
Adjusting the preset profile setting rail: Set
ting the parallelism
► Set the stop rail [6-7] at a right angle to the
saw blade (see section 9.5).
► Undo the hexagon socket head
screws [6-14].
► Place a protractor between the saw blade
and the sliding handle [6-2].
► Using the protractor, adjust the sliding han
dle [6-2] to 90°.
► Tighten the hexagon socket head
screws [6-14].
9.6 Table insert
Removing the table insert
► Open the table insert [7-1] with a span
ner [7-2] in the direction of the arrow.
► Remove the table insert [7-1].
Fitting the table insert
► Insert the table insert [7-1] into the table
and lock it into place.
WARNING
Risk of accidents due to kickback
► Make sure that the table insert is correctly
inserted and forms an even surface with
the saw table.
9.7 Guard
Fitting the guard
► Set the saw blade to maximum cutting
height (see section 9.3).
► Set the inclination angle to 0° (see section
9.4).
► Unscrew the screw [8-2] from the
guard [8-1].
► Insert the lengthwise pin situated in the
guard [8-1] into the groove [8-4] of the
spacer wedge [8-5].
► Re-insert the screw [8-2] into the
guard [8-1] and through the hole in the
spacer wedge [8-3] and tighten it.
Removing the guard
► Set the saw blade to maximum cutting
height (see section 9.3).
English
39
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TKS 80 EBS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TKS 80 EBS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info