778502

Festool TKS 80 EBS Manual

38
Zoom out
Zoom in
Previous page
1/276
Next page
Brake
The saw blade is stopped electronically within
approx. 3 seconds of switching off the machine.
Restart protection
The built-in restart protection prevents the
power tool from starting up again automatically
if the power is disconnected during continuous
use. To put the power tool back into operation,
it must first be switched off and then on again.
9.2 Selecting the saw blade
Festool saw blades are identified by a coloured
ring. The colour of the ring represents the ma
terial for which the saw blade is suited.
Refer to the necessary saw blade data (see sec
tion 3.1).
Colour Material Symbol
Yellow Wood
Red Laminate, mineral ma
terial
HPL/TRESPA
®
Blue Aluminium, plastic
"$3:-
9.3 Setting the cutting height
To set the cutting height anywhere be
tween 0 mm–80 mm:
► Turn the cutting height setting [5-5].
+ Increases the cutting height to 80 mm
- Decreases the cutting height to 0 mm
To ensure a precise saw cut, set the cut
ting height 2 mm–5 mm greater than the
workpiece thickness.
For concealed cuts, the cutting height is
set in accordance with the required depth
of the concealed cut.
9.4 Setting the inclination angle
The saw blade can be swivelled between 0° and
45°, and can be precisely adjusted by ±2° to -2°
and 47°.
► Press and hold the inclination angle set
ting [5-3] against the cutting height set
ting [5-5].
► Move the inclination angle setting [5-3]
along the scale [5-1] until the angle indica
tor [5-2] points to the required angle.
► Release the inclination angle setting [5-3]
and cutting height setting [5-5].
For precision trimming work, swivel out the
saw blade by 2° beyond the two end positions in
each case:
Fine adjustment
► Set the inclination angle to 0° to set a fine
adjustment of up to -2°.
Set the inclination angle to 45° to set a fine
adjustment of up to 47°.
► Turn the rotary handle for fine adjust
ment [5-4].
+ End position up to 47°
- End position up to -2°
0 Zero position
End positions 0° and 45° are active.
9.5 Preset profile setting rail
The preset profile setting rail can be set as a rip
fence (Fig. 6a) and as a cross stop or angle
stop (Fig. 6b).
WARNING
Risk of accidents due to tools
► The stop rail [6-7] must not protrude into
the cutting areas.
► All screws and rotary knobs of the preset
profile setting rail must be firmly tightened
when sawing.
Installation of the preset profile setting rail
The supplied preset profile setting rail can be
attached to all four V-profiles [6-12].
► Release the rotary knob [6-1].
► Insert the preset profile setting rail [6-10]
into a V-profile [6-12].
► Adjust the hexagon socket head
screws [6-9] to stabilise the preset profile
setting rail [6-10] guidance in the V-pro
file [6-12].
► Adjust the ball bearing [6-13] in order to
adjust the preset profile setting rail [6-10].
► Slide the preset profile setting rail [6-10] in
the V-profile [6-12] until the preset profile
setting rail [6-10] covers the field marked
in green on the table side [6-11].
► Tighten the rotary knob [6-1].
Preset profile setting rail as rip fence
► Undo the screw [6-4].
► Lift the fixing pin [6-3].
► Set the angle [6-5] to 0° using the scale.
► Click the fixing pin [6-3] into place.
► Tighten the screw [6-4].
► Undo the screw [6-6].
English
38
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TKS 80 EBS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TKS 80 EBS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info