778502

Festool TKS 80 EBS Manual

40
Zoom out
Zoom in
Previous page
1/276
Next page
► Set the inclination angle to 0° (see section
9.4).
► Tighten the guard [8-1] and unscrew the
screw [8-2].
► Pull the lengthwise pin situated in the
guard out of the groove [8-4] of the spacer
wedge [8-5] and remove the guard [8-1].
► Re-insert the screw [8-2] into the
guard [8-1] and tighten it.
Setting the guard
► Release the rotary knob [8-8].
► To adjust the preset profile setting rail, lock
the side splinter guard of the guard [8-6]
with the snap-in nose [8-7] in the top posi
tion.
► Lift the guard into the top position and
tighten the rotary knob [8-8].
► After adjusting the preset profile setting
rail, loosen the rotary knob [8-8] again and
unhook the side splinter guard of the
guard [8-6].
The guard [8-1] and the splinter guard
of the guard [8-6] must lie freely on
the plate.
9.8 Replacing the riving knife
Use a riving knife with guard [9-1] for rip
and angled cuts.
Use a riving knife for grooving [9-2] for
non-through cutting.
WARNING
Risk of accidents due to kickback
► The safety equipment must be re-installed
immediately after work that requires the
spacer wedge with protective cover to be
removed.
With fitted table insert
► Set the cutting height to the maximum of
80 mm (see section 9.3).
► Remove the hex key [9-4] from the hold
er [9-5].
► Fully insert the hex key [9-4] into the open
ing [9-3].
► Turn the hex key [9-4] clockwise as far as it
will go.
► Remove and/or replace the riving knife
(Fig. 9c).
► Turn the hex key [9-4] anticlockwise as far
as it will go.
► Remove the hex key [9-4] and store it in the
holder [9-5].
With removed table insert
► Turn the lever handle [9-6] clockwise as far
as it will go.
► Remove and/or replace the riving knife
(Fig. 9c).
► Turn the lever handle [9-6] anticlockwise as
far as it will go.
9.9 Dust extraction
WARNING
Hazardous dust
Damage to the respiratory passage
► Always work with an extractor.
► Comply with national regulations.
► Wear a dust mask.
The TKS 80 EBS has two vacuum connections
with bayonet coupling:
An upper vacuum connection [10-1] with a di
ameter of 27 mm and a lower vacuum connec
tion [10-4] with a diameter of 36 mm.
► To guide the upper extractor hose, attach
the extractor hose holder [10-2] to one of
the V profiles.
The extractor set [10-3] joins both vacuum con
nections to enable a Festool mobile dust ex
tractor with an adapter of 50 mm in diameter to
be connected.
9.10 Saw blade cover
Opening the saw blade cover
► Loosen the screw [11-1] and remove both
keys.
► Release the rotary knob [11-2].
► Open the top [11-3] with a spanner for the
spindle flange [11-5] or with a suitable
screwdriver.
► Open the saw blade cover [11-4].
Closing the saw blade cover
► Insert the saw blade cover [11-4].
► Close the top [11-3] with a spanner for the
spindle flange [11-5].
► Insert both open-ended spanners and tight
en the screw [11-1].
► Tighten the rotary knob [11-2].
English
40
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TKS 80 EBS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TKS 80 EBS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info