796183
22
Zoom out
Zoom in
Previous page
1/129
Next page
Constant speed
The preselected motor speed is kept constant
through electronic control. This ensures a uni
form speed even when under load.
Temperature cut-out
To avoid the motor overheating, the power con
sumption is limited at an excessive motor tem
perature (e.g. if the pressure is too high while
working). If the temperature continues to rise,
the power tool switches off. It can only be
switched on again once the motor has cooled
sufficiently.
6.3 Handle position
Loosen the handle screw [1-5] as much as nec
essary and set the handle [1-6] to a suitable
working position by tilting it. Then tighten the
handle screw [1-5] again.
6.4 Sanding discs
Depending on the application area, various
sanding discs are available. Use solely discs of
Festool, which guarantees the sanding output
of the RG 130 ECI.
Recommended sanding disc types
Sanding
disc
Field of application Speed
range
DIA STONE-D130
Very hard materials,
e.g. concrete with a
strength higher than
C20, cast concrete
6
DIA HARD-D130
Hard materials, e.g.
concrete with a
strength higher than
C10, hard screed
6
DIA ABRASIV-D130
Soft materials with a
higher level of abrasion,
e.g. fresh concrete, ad
hesive coatings, hard
plaster, sandstone
6
Sanding
disc
Field of application Speed
range
DIA PAINT-D130
Large and thick layers
of paint or varnish, e.g.
on floorboards, wooden
façades and doors
4–6
DIA THERMO-D130
Tough and thermoelas
tic materials, e.g. pro
tective coatings, elastic
adhesives
5–6
Installing the abrasive wheel
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
WARNING
Risk of injury from the fragile sanding tool
Ensure that the sanding tool's expiry date
has not been exceeded.
Clean the flange [2-1] and fastening
nut [2-4] as well as sanding disc fastening
areas [2-2].
Mount sanding disc. Flange fitting must fit
the sanding disc aperture.
Press in the spindle blocking plunger [2-3].
Press in the blocking plunger only when de
vice is switched off and spindle not active.
Turn the spindle [2-6] until blocking plung
er fits in.
Screw the fastening nut by fitting it from the
sanding disc on the spindle.
Fasten the fastening nut with key [2-5].
Before starting the device, make sure the
sanding disc rotates smoothly.
The intermediate layers supplied with the
sanding discs are not required.
6.5 Brush
Lifting the front brush
For wall lifting, it is possible to lift the lifting
segment [3-1] (see figure [3]).
English
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool RG 130 ECI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool RG 130 ECI in the language / languages: All languages as an attachment in your email.

The manual is 2.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info