Manual Festool of 2200 eb set (page 16 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

427177

Zoom out

Zoom in

1/116

Clamp the machine in this position by tighten-

ing the rotary knob [5.1].

Press the depth stop [5.3] against one of the

three ﬁ xed stops on the rotary stepped stop

[5.4].

Slide the indicator [5.5] down to the 0 mm mark

on the scale [5.7].

 If the base position of the indicator is incor-

rect, this can be adjusted by turning the screw

[5.6] on the indicator.

The stepped stop [Fig. 7] has three stops, two of

which can be adjusted in height using a screw-

driver:

Stop Height

A 18 mm - 51 mm

B 6 mm - 18 mm

C 0 mm

 Stop C has an offset for preliminary routing -

see "Preliminary/Fine routing".

b) Presetting the routing depth

Pull the depth stop [6.6] upwards until the indi-

cator [6.2] reaches the required routing depth.

Clamp the depth stop in this position using the

clamp lever [6.3].

Unscrew the rotary knob [6.1]. The machine is

now in starting position.

If necessary, you can readjust the routing depth

by turning the adjusting wheel [6.8]. Each mark

represents a routing depth of 0.1 mm. One com-

plete turn of the wheel is 1 mm.

 The dial ring [6.7] can be turned separately to

the "zero" setting.

 The three marks [6.4] indicate the maximum

adjustment range of the adjusting wheel

(20 mm) and the central position when aligned

with the edge [6.5].

7.5 Preliminary/Fine routing

Stop C has two stop limits with a height difference

of 2 mm. Routing to the depth preset with stop C

can be performed in two steps:

Lower the router to the ﬁ rst stop level [7.1] for

the preliminary routing step;

Lower the router to the second stop level [7.2]

to complete the routing procedure.

 This procedure enables rapid routing to a con-

siderable depth while still achieving a good

surface quality. The ﬁ nal routing depth is de-

ﬁ ned by adjusting the stop level [7.2].

7.6 Fine adjuster for edge trimming

The machine has a special ﬁ ne adjuster for rout-

ing tools with a bearing guide, which allows quick

and easy precision adjustment prior to rounding

edges and prevents offsets [Fig. 8].

First of all, roughly preset the routing depth and

perform a test run.

Then adjust the routing depth more precisely:

Open the clamping lever [9.2].

Push the depth stop [9.3] against the ﬁ xed stop

C [9.5].

 Clamp the depth stop using the eccenter [9.4] on

the stepped stop (turn clockwise).

Close the clamping lever [9.2].

Unscrew the rotary knob [9.1].

Turn the adjusting wheel [9.6] to set the routing

depth more precisely.

 The routing depth can be adjusted in both di-

rections because the depth stop is connected

to the stepped stop.

Tighten the rotary knob [9.1].

Open the eccenter [9.4] (turn anticlockwise).

Perform more test runs and make the appro-

priate adjustments if necessary.

7.7 Dust extraction

CAUTION

Breathing in dust can damage the respiratory

passage.

Always connect the machine to a dust extractor.

Only work with the chip guard [10.2] in perfect

working order.

When performing work that generates dust,

always wear a dust mask.

A Festool dust extractor with an extractor hose

diameter of 36 mm or 27 mm (36 mm recom-

mended due to the reduced risk of clogging) can

be connected to the extractor connector [10.4]

The extractor connector [10.4] can be rotated

within the range indicated [10.3]. The extractor

connector on the extraction pipe will no longer be

secure if rotated outside of this range.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool of 2200 eb set in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool of 2200 eb set Manual

Product: