Manual Festool of 2200 eb set (page 17 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

427177

Zoom out

Zoom in

1/116

Chip guard

The chip guard [10.2] can be moved to the top po-

sition to change the router bit, for example. Slide

the chip guard upwards until it engages or push

the machine down as far as possible.

We recommend lowering the chip guard before

starting work to improve the efﬁ ciency of the ex-

traction system. Push the lever [10.1] towards the

handle to do this.

KSF-OF chip deﬂ ector

The chip deﬂ ector KSF-OF [11.1] indirectly in-

creases the efﬁ ciency of the extraction system

during edge routing. The maximum possible rout-

ing diameter is 78 mm.

The deﬂ ector is ﬁ tted in a similar way to the copy-

ing ring (see "Copy routing").

The hood can be cut off along the grooves [11.2]

using a hacksaw and can thus be reduced in size.

The chip deﬂ ector can then be used for interior

radiuses up to a minimum radius of 52 mm.

8 Operation

WARNING

Risk of accident - read the following instruc-

tions:

Always secure the workpiece in such a man-

ner that it cannot move while being routed.

Always hold the machine with both hands and

by the handles [2.4] available.

Always switch on the router before bring-

ing the router bit into contact with the work-

piece!

Before starting work, make sure that the

clamp lever [1.6] is closed and the eccenter

[1.7] is open.

Always ensure that the cutting power of the

machine works against the feed direction of

the machine (up-cut routing).

Procedure

Preset the required routing depth.

Switch on the machine.

Unscrew the rotary knob [1.3].

Push the machine down as far as possible.

Clamp the machine in this position by tighten-

ing the rotary knob [1.3].

Perform the routing task.

Unscrew the rotary knob [1.3].

Move the machine slowly upwards to the stop.

Switch off the machine.

8.1 Machine guidance methods

a) Routing with side stop

The side stop (partly as an accessory) is positioned

parallel to the workpiece edge.

Secure both guide rods [12.4] with the two rotary

knobs [12.2] on the side stop.

Insert the guide rods into the grooves on the

router base to the required distance and secure

them by turning the rotary knob [12.1].

Fine adjustment

Unscrew the rotary knob [12.7] to make ﬁ ne

adjustments with the adjusting wheel [12.5].

The dial ring [12.6] has a 0.1 mm scale for this

purpose. If the adjusting wheel is held secure,

the dial ring can be turned separately and set to

"Zero". The millimetre scale [12.3] on the main

casing is useful for making larger adjustments.

Tighten the rotary knob [12.7] again after com-

pleting any ﬁ ne adjustments.

Adjust both guidance jaws [13.3] so that they

are approx. 5 mm from the router bit. To do this,

undo screws [13.2] and tighten again after com-

pleting the adjustments.

Only when routing along an edge: slide the ex-

tractor hood [13.1] until it latches into position

on the side stop and connect an extraction hose

27 mm or 36 mm in diameter to the extractor

connector [13.4]. Alternatively, leave the machine

to extract the dust via the extractor connector.

b) Copy routing

When routing with templates, ﬁ t an integrated cop-

ying ring to the router (accessory).

 Copying rings can be used in combination with

the standard base runner. A special base run-

ner is available as an accessory to improve the

contact surface.

CAUTION

An excessively large routing tool may damage

the copying ring and cause accidents.

Make sure that the routing tool used ﬁ ts through

the opening on the copying ring.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool of 2200 eb set in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool of 2200 eb set Manual

Product: