Manual Festool of 2200 eb set (page 15 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

427177

Zoom out

Zoom in

1/116

Routing tool diameter

[mm]

Recommended

cutting material

Material

10 -30 30 - 50 50 - 89

Adjusting wheel setting

Chipboard,

coated

6 - 5 6 - 4 4 - 2

Plastic

6 - 4 6 - 3 3 - 1

Aluminium

3 - 1 3 - 1 2 - 1

HSS

(HW)

Plasterboard

2 - 1 1 1

Constant speed

The preselected motor speed remains constant

through electronic control. This ensures a uni-

form cutting speed even when under strain.

Temperature cut-out

To protect against overheating (burning out of

motor), an electronic temperature monitoring

system has been installed. Prior to reaching a

critical motor temperature, the safety electronics

switches off the motor. After a cooling time of ap-

prox. 3-5 minutes, the machine can be operated

again at full load. The machine requires less time

to cool down if it is running, i.e. in neutral.

Brake

The OF 2200 EB has an electronic brake, which

stops the spindle within a few seconds of the ma-

chine switching off.

7.2 Changing tools

WARNING

Risk of accident - the routing tool may be hot

after use and has sharp edges.

Allow the tool to cool before changing.

 Wear protective gloves when changing tools.

NOTE

Switch off the machine before pressing the rocker

for the spindle lock [3.1].

We recommend turning the machine on its side to

change the tool.

a) Inserting the tool

Insert the routing tool [3.4/3a.1]] into the open

clamping collet as far as possible, but at least

up to the mark

on the shank [3a.2]. If the

collet is not visible because it is blocked by the

union nut [3a.3], the milling tool must be insert-

ed into the collet at least far enough that the

marker

no longer overlaps with the union

nut.

Press the rocker [3.1] for the spindle lock to

side B.

Tighten the locking nut [3.3] using an open-end

wrench (size 24).

 The rocker only blocks the motor spindle in

one direction of rotation at any one time.

Therefore when the locking nut is undone or

tightened, the wrench does not need to be

offset but can be moved back and forth like a

ratchet.

b) Removing the tool

Slide the chip guard [3.2] upwards until it en-

gages, if necessary.

Press the rocker [3.1] for the spindle lock to

side A.

Unscrew the locking nut [3.3] using an open-

end wrench (size 24) until you are able to re-

move the tool.

7.3 Changing the clamping collet

If necessary, slide the chip guard [4.2] upwards

until it engages.

Press the rocker [4.1] for the spindle lock to

side A.

Unscrew the locking nut [4.3] completely.

Remove the locking nut from the spindle to-

gether with the clamping collet [4.4]. Do not

separate the locking nut and clamping collet as

these form a single component.

Only insert a new clamping collet in the spin-

dle when the nut is attached and engaged, then

tighten the nut slightly. Do not tighten the lock-

ing nut until a router bit is inserted.

7.4 Adjusting the routing depth

The depth is adjusted in two steps:

a) Setting the zero point

Place the router on an even surface (reference

surface).

Open the clamping lever [5.2].

Unscrew the rotary knob [5.1].

Push the machine downwards until the router

bit rests on the surface (reference surface).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool of 2200 eb set in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool of 2200 eb set Manual

Product: