Manual Ferm CSM1051 (page 11 of 56) (English, German, Dutch, French)

798918

Zoom out

Zoom in

1/56

off switch (4); the device will run at maximum

speed. Release the switch lock (3).

5. The device will switch off again when you

release the on/off switch (4). The device

cannot be switched to continuous operation.

Changing the blade bar

1. Switch off the device and remove the battery

(14) from the device.

2. Place the device on a level surface.

3. Turn the mounting knob (10) of the sprocket

cover in a counter-clockwise direction in order

to loosen the chain tension and to remove the

sprocket cover (9).

4. Remove the blade bar (11) and saw chain (12).

To disassemble, hold the blade bar (11) tilted

upwards at an angle of approx. 45 degrees in

order to be able to remove the saw chain (12)

more easily from the chain sprocket (17).

5. Replace the blade bar and install the blade bar

and saw chain as described under “Installing

the saw chain and blade bar”.

The tensioning of the saw chain is described in

the “Assembly” section.

SAWING TECHNIQUES

General information

Observe noise protection rules and other

local regulations when working with the

tool. Local regulations may require a

suitability test.

• Dirt, stones, loose bark, nails, clips and wires

must be removed from the tree.

• Always stand above the tree trunk when

sawing on slopes.

• To keep total control while sawing through,

reduce the pressure at the end of the cut

without loosening your grip on the handles

of the pruner saw. Make sure the saw chain

does not touch the ground. After finishing the

cut, wait until the pruner saw comes to a stop

before removing it.

• Always switch off the motor of the pruner saw

before changing between trees.

• You will have better control over the device if

you saw using the lower edge of the blade bar

(chain in pulling direction).

• The saw chain must not touch the ground or

any object while sawing through the material

or thereafter.

• Ensure that the saw chain does not get stuck

while sawing. The log must not break or splinter.

• Please also observe the precautionary

measures to protect against kickback (see the

safety information).

• For sawing work on hillsides, always stand in

the area above the log. To keep total control

while sawing through, reduce the pressure at

the end of the cut without loosening your grip

on the handles of the pruner saw. Make sure

the saw chain does not touch the ground.

After finishing the cut, wait until the saw chain

comes to a stop before removing it. Always

switch off the motor of the pruner saw before

changing between trees.

If the saw chain gets stuck, do not

attempt to pull out the device with force.

There is a risk of injury. Turn the motor off

and use a lever arm or wedge to release

the device.

Cut to length

Cutting to length means sawing felled tree trunks

into small sections. Ensure that you have secure

footing and balance your body weight evenly

on both feet. If possible, the trunk should be

protected and supported by branches, logs or

wedges.

• Make sure that the saw chain does not touch

the ground when sawing.

• Make sure you have good footing and stand

above the trunk on sloping terrain. To keep

total control while sawing through, reduce

the pressure at the end of the cut without

loosening your grip on the handles of the

pruner saw. After finishing the cut, wait

until the saw chain comes to a stop before

removing it. Always switch off the motor of the

pruner saw before changing between trees.

1. Log is lying on the ground:

Saw through the log completely from above and

ensure at the end of the cut not to contact the ground.

If you can turn the tree trunk, saw twothirds of the

way through it. Then turn the trunk around and

saw the rest of the way through from above.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6.87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1051 Manual

Product: