798918
13
Zoom out
Zoom in
Previous page
1/56
Next page
13
EN
oil on the joints and on the tooth tips of the
individual chain links.
1. The chain should be well-tensioned to ensure
proper sharpening.
2. For the sharpening, a round file with 4.0 mm
diameter is necessary.
Other diameters damage the chain and
can lead to danger during work!
3. Sharpen only from the inside to the outside.
Guide the fi le from the inner side of the cutting
teeth to the outer side. Lift the fi le when you
are withdrawing it.
4. Sharpen first the teeth on one side. Turn the
saw around and sharpen the teeth of the other
side.
5. The chain is worn and must be replaced by
a new saw chain if only approx. 4 mm of the
cutting teeth is remaining.
6. After the sharpening, all cutting elements must
now be equal in length and width.
7. After every third sharpening, the sharpness
depth (depth limitation) must be checked and
the height filed with the aid of a flat file. The
depth limitation should be set back about 0.65
mm from the cutting tooth. After the setting
back of depth limitation, round it off a little at
the front.
Adjusting the chain tension
The adjustment of the chain tension is described
in the chapter “Assembly - tensioning chainsaw”.
Switch off the device and remove the battery
(14) from the device.
Check the chain tension regularly and re-
adjust this as often as possible. When the saw
chain is tensioned with 9 N (approx. 1 kg), the
gap between the saw chain and the guide rail
may not be more than 2 mm.
Starting up a new saw chain
In the case of a new chain, the tensioning force
decreases after some time. Therefore, you have
to re-tension the chain after the first 5 cuts and no
later than after 10 minutes’ sawing time.
Never attach a new chain to a worn drive pinion
or place onto a damaged or worn chain bar. The
chain could spring back or break, potentially
leading to serious injury.
Maintaining the chain bar
Use cut-protection gloves when
handling the chain or the chain bar.
1. Switch off the device and remove the battery
(14) from the device.
2. Remove the sprocket chain wheel covering (9),
the saw chain (12) and the chain bar (11).
3. Check the chain bar (11) for wear. Remove
burrs and straighten the guide surfaces with a
flat file.
4. Mount chain bar (11), chainsaw (12) and
sprocket chain wheel covering (9) and tighten
the saw chain.
Turning the blade bar
Use cut-resistant gloves when working
with the saw chain or with the blade bar.
The blade bar (11) needs to be reversed regularly
after a working time of about 10 hours in order to
ensure even wear.
1. Switch off the device and remove the battery
(14) from the device.
2. Remove the sprocket cover (9), saw chain (12)
and blade bar (11).
3. Turn the blade bar around its horizontal
axis and install the blade bar and chain as
described under “Installing the saw chain and
blade bar”.
When doing so, pay attention to the correct
rotation direction of the saw chain!
Direction of travel of saw
chain
Use the graphical symbol above the chain
sprocket (17) as a guide to align the saw chain
(12) when the blade bar is rotated. The illustrated
direction of travel on the blade bar is no longer
true.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CSM1051 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info